Takes several times to start car

ANSWER : The issue you are having is probably due to an intermittent fault in the starter motor itself or a deficiency in the starter electrical circuit, for example a large voltage drop due to a poor ground or a high resistance connection. These issues can be readily diagnosed and resolved on a mobile basis if you request a hard starting diagnostic. If you request that diagnostic, the responding certified mechanic will get this resolved for you promptly. Based on Toyota’s Factory Service Manual, the battery should not be disconnected if the vehicle engine is running. The battery acts as a large resistive voltage sink and consequently taking the battery out of the circuit, while the alternator is still running, can create a voltage spike on the car’s electrical system which is not good for voltage sensitive components such as the engine computer. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Of course, don’t switch gears without being fully stopped, unless your Owner’s Manual or the manufacturer has alternative advice. However, the gear shift issue has no relation to the no-start problem you are describing. Inasmuch as you only have 6,000 miles on the car, the "constant on and off" that you believe has occurred is meaningless in comparison to the expected total vehicle service life. That is, assume what you perceive as "constant on and off", during merely 6,000 miles, might be equivalent to using the car "normally" for three years. A new car should be trouble free for at least 5 years, unless there is a defect, so your "constant on and off" is not a causal factor for any fault on the vehicle. What you might have is a defect in the ignition switch, or perhaps the immobilizer system, but if the problem is not in the switch itself, clearly there is an electrical problem.

If your vehicle is under warranty, by law the dealer MUST repair the issue you are describing within a prescribed time frame and number of "attempts", otherwise the dealer will run afoul of Federal and state Lemon Laws that give you very specific rights, and recourse (contact an Attorney; we are Mechanics, NOT attorneys). Consequently, if the vehicle is still under warranty, to save yourself money do be sure to seek a resolution from the dealer. If the vehicle is not under warranty, obviously a certified Mechanic from YourMechanic could identify the electrical fault and resolve this for you. If you want to go that route, please simply request a no start diagnostic -electrical system and the responding certified mechanic will get this taken care of for you. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : There are reports that the replacement alternators will not communicate with the engine computer and will not charge correctly. I recommend using only the manufacturer approved replacement part. It can be new or remanufactured but approved for use in the vehicle. Some lower cost alternators on the aftermarket will have charging problems since they will not communicate with the ECM on the vehicle and will stop charging.

ANSWER : Hi There,
The EPC light is typically related to the ECM (computer) not receiving the proper signal from the crankshaft position sensor. A crankshaft position sensor is an electronic device used to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control the fuel injection or the ignition system timing and other engine parameters. When this is faulty or not working properly, this will cause problems with the ignition system and generating spark transmission to the spark plugs resulting in starting problems and other performance issues causing misfires. I would recommend having an expert from YourMechanic come to your location to diagnose and inspect your vehicle.

ANSWER : Hello there. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. Some common parts that cause this include mass air flow sensors, damaged or clogged fuel injectors, or the throttle body being damaged. The best way to diagnose the right cause of this problem is to have a mobile mechanic come to your location and complete a car starts then dies inspection.

ANSWER : Your MAP sensor is an important input for your computer. It helps determine the load on the engine to calculate the correct amount of fuel to inject. It sometimes takes a few seconds for the vehicle to realize that the sensor is not producing a good signal.

At that point, it will use other methods to determine the fuel rate, such as pre-programmed fuel maps, throttle position, etc. I would suggest replacing the MAP sensor and retesting. If you would like to have it checked first, a certified technician from YourMechanic will be able to scan your vehicle and test components to determine the root cause of your starting issue before making a repair.

ANSWER : Hi there:

Sometimes when you have problems starting an engine initially it is caused by a restriction in fuel flow; caused either by clogged fuel injectors or the throttle body that needs to be cleaned. Once the fuel starts to flow and engine warms up, it’s much easier to start. However, it could also be an air filter, EGR valve or other components that causes this issue as well, which is why it’s best to have a professional mobile mechanic complete a car is hard to start inspection so they can pinpoint the source of this issue.

ANSWER : The first thing I would do is have the turbo/intake system ’smoke’ tested or visually inspected for any leaks. Without a smoke machine, you could spray your engine and turbo system with brake cleaner and listen for idle changes to help determine if there is a leak. The brake cleaner method is not as effective as using a smoke machine.

Next, checking your fuel pressure is in order to see if you lose fuel pressure as it sits or if the fuel pump in the tank is weak. If the fuel pump in the tank is weak or losing pressure, it would cause the engine to crank as you mentioned. Performing a fuel pressure test is not easy and requires a special tool. If you want to have this looked at a technician from YourMechanic can come to your car’s location to diagnose your stalling issue.