What are the different seat belt locking modes used?
What are the different seat belt locking modes used?
Experienced mechanics share their insights in answering this question :
The days when seat belts were just seat belts are largely behind us. Your car actually has a sophisticated restraint system that’s capable of offering two different locking modes for the seat belts in your car.
Vehicle Sensitive Mode: This is the only locking mode used for the driver front seat belt, but the passenger front and rear belts can use this mode, as well as Automatic Locking mode. In Vehicle Sensitive mode, the shoulder belt is free to move so you can adjust it, but will lock under certain conditions (sudden stops, for instance).
Automatic Locking Mode: This mode keeps the shoulder belt locked so that it will not extend. You’ll need to engage this mode manually. It’s especially important for securing car seats and booster seats in the car, but can be used in other situations.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
Most seat belts have locking mechanisms built into the retracting mechanism. Called an Automatic Locking Retractor (ALR), this seat belt design is a safety feature intended to hold a child car seat in place.
The Emergency Locking Retractor (ELR) allows the driver seat belt to freely extend and retract with occupant movement, yet locks the belt during a sudden stop or upon impact. The Automatic Locking Retractor (ALR) makes it possible to secure a child seat without using a seat belt locking clip.
Vehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Convenience Buttons
Some vehicle seat belts include a button that`s attached to the seat belt. This button helps keep the latchplate in place so it doesn`t drop all the way to the bottom of the belt when the seat belt isn`t in use.
General Description. The sensor detects whether the seat belt buckle is latched or unlatched, allowing the passenger safety system to determine the optimum airbag deployment. It is also used as an input to the electronic park brake and the unbuckled warning system. Benefits.
Hint: ELR or the environmental lapse rate works antagonistically to the ALR or the adiabatic lapse rate. Hence when there is an increase in the environmental lapse rate, the adiabatic lapse rate becomes unstable.
Your vehicle is equipped with pre-tensioner seat belts at the front seating positions. The purpose of the pre-tensioner is to make sure that the seat belts fit tightly against the occupant`s body in certain collisions. The pre-tensioner seat belts may be activated in crashes where the collision is severe enough.
The mode of a lock tells what access to the locked object is permitted to the lock owner and to any concurrent processes. Db2 uses of the lock modes to determine whether one lock is compatible with another. Some lock modes do not exclude all other users.
A shared lock reserves a resource (page or row) for reading only. Other processes cannot modify the locked resource while the lock remains.
A typical seat belt consists of a lap belt, which rests over your pelvis, and a shoulder belt, which extends across your chest. The two belt sections are tightly secured to the frame of the car in order to hold passengers in their seats.
Most seat belts have two parts. A lap belt that goes over the wearer`s pelvis, and the shoulder belt which extends over one shoulder and across the chest.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
What are the different seat belt locking modes used?
ANSWER : The days when seat belts were just seat belts are largely behind us. Your car actually has a sophisticated restraint system that’s capable of offering two different locking modes for the seat belts in your car.
Vehicle Sensitive Mode: This is the only locking mode used for the driver front seat belt, but the passenger front and rear belts can use this mode, as well as Automatic Locking mode. In Vehicle Sensitive mode, the shoulder belt is free to move so you can adjust it, but will lock under certain conditions (sudden stops, for instance).
Automatic Locking Mode: This mode keeps the shoulder belt locked so that it will not extend. You’ll need to engage this mode manually. It’s especially important for securing car seats and booster seats in the car, but can be used in other situations.
hey i had a belt break while traveling on my 2004 honda pilot. It is the small belt and not the serpentine belt. The mechanic t
ANSWER : Hello. The smaller belt is known as your timing belt, and it works inside the engine to keep mechanical components aligned with each other during the compression cycle. The serpentine belt, which is the big belt, drives the alternator, water pump, AC compressor, and a couple of other components. If the small belt broke it is likely the timing belt. This will cause the car to stall, lights to illuminate, and can even cause serious damage to the engine. Typically replacing a timing belt is a lot more complicated and expensive than replacing a serpentine belt. You may want to receive a second opinion on the car before you go ahead with repairs.
Front Passenger Lock sometimes does not lock with a remote control or by locking button located on either doors.
ANSWER : The solenoid is on the door latch and is most likely the cause of the problem for your 2005 Toyota Tacoma. If you want to have this inspected and repaired, a certified technician from YourMechanic can come to your home or office to diagnose your door lock and perform the correct replacement.
How do you reset the seat belt light on a 2006 Murano?
ANSWER : You will need to have your body computer scanned to get the codes from the seat belt module. If may have stored the code due to the battery was not disconnected when seat was removed causing the system to see problems in seat circuits. You may just have to have the codes cleared and if no problem codes return the you will be okay.
all doors lock only by inserting key in passenger side door and locking
ANSWER : Your central locking system may have been designed with a control module in the circuit. This is a small computer that is responsible for controlling the different functions of a particular system. It is possible that the module for your central locking system may have shorted out internally preventing particular functions from working properly. I would recommend having a certified technician test your central locking module to determine if all of its functions are working properly.
Car Seat and Seat Belt Issue
ANSWER : You may have open recalls for the seat belts on your vehicle. I would call the local dealer to verify open recalls for the seat belts and repair for them may be free of charge. The seat being broken is most likely not repairable and need to replace the seat.
How do I set the seat belts in automatic locking mode?
ANSWER : Automatic locking mode is a feature that keeps the seat belts from having any slack. This feature should always be used when attaching a child restraint system. To set the system, follow these steps:
1. Buckle the seat belt.
2. Pull the shoulder strap downward until the entire belt is extracted from the retractor. If the belt is an inflatable belt, then instead of this step, pull the lap belt upward until the entire belt is extracted.
3. Release the belt and allow it to retract.
4. Try and move the belt to make sure that it is locked.
How do you engage automatic locking mode on the seat belts?
ANSWER : Your seat belts can be set to vehicle sensitive mode, which allows the shoulder belt to extend and retract as you need it. It will automatically lock when the system detects sudden deceleration while you’re traveling at over 5 MPH. However, you can also set your seat belts (the passenger front and all rear seat belts) to automatic locking mode. Here’s how to do that:
Connect the buckle and the seat belt tongue.
Pull the shoulder belt down until it is completely extended from the retractor.
Let the belt retract. It should make a clicking sound. If you don’t hear it clicking, automatic locking mode is not engaged.
To deactivate automatic locking mode, just release the buckle and let the seat belt retract.
Tip
Automatic locking mode must be engaged again every time you unbuckle the seat belt.
