when I turn my ac on my cars idle drop and stalls out and the ac is hot

ANSWER : Hello, thank you for writing in. Although the pulley is still spinning, the compressor has likely failed. If it is not properly regulating pressure in the system, one of the first signs is a warm air conditioner. Considering yours is not cooling off, the pressures are not correct. If you believe the compressor is working correctly, you may want to check for a clogged line before replacing it. Keep in mind, a blocked line has likely put extra strain on the compressor, and may cause premature failure. For more help with testing or replacing the compressor, contact our service department to schedule an appointment.

ANSWER : The control circuit for the fans needs to be checked. For example, there is usually a condenser fan relay in the A/C electrical controls. There could be a fault with that relay and/or wiring problems, perhaps even just a loose connection, blown or loose fuse, and so forth. To resolve something like this, the recommended service is an electrical component diagnostic. If you request that diagnostic service, the responding certified mechanic will get the problem pinpointed and resolved. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Hello – your symptoms suggest worn piston rings or valve stem seals (smoking), and a possible air leak in the intake, or idle air control valve sticking open (high idle). Both are signs of a higher-mileage engine with significant wear. I recommend an engine inspection performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, and give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hi there. Check all of the grounds to the vehicle and see if there is any wires that are damaged from the taillight short. A loose ground will cause multiple problems with the electrical system and some or multiple components will not work. If you need further assistance with your electrical issues, then seek out a professional, such as one from Your Mechanic, to help you.

ANSWER : Your probably correct, it sounds as though your battery is done. But it also sounds like you have charging system issues. I’m not sure that fixing your battery and charging system will solve the problem with the car shutting off, but it’s possible that it will and it’s a darned good place to start. By contacting Your Mechanic, you can have a technician come to your home or office to check out your car and help you figure out what to do next.

ANSWER : Hello there. The charging system on the car may not be charging the battery as you drive and the systems that keep the engine running are priority so the engine will stay running until the voltage drops below about 9 volts but the lighting and some other accessories may cut off above this voltage first. You should have the charging system tested to see if the alternator needs to be replaced.

ANSWER : There are two principal possibilities: faulty motor/transaxle mounts, or an engine operating or mechanical condition including the possibility of a faulty harmonic balancer. To obtain a conclusive diagnostic, please simply request an engine vibration diagnostic and a certified Mechanic, dispatched by YourMechanic right to your location, will get this resolved. If you do need new motor/transaxle mounts, genuine OEM Nissan mounts are recommended in order to maximize the chances of resolving the problem. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Hi there.The catalytic converter has two oxygen sensors. One oxygen sensor is positioned in front (upstream) of the catalytic converter and the other oxygen sensor is positioned at the rear (downstream). If the upstream oxygen sensor is working properly, its readings should fluctuate from when the car is at operating temperature and when running in a closed loop. When the oxygen sensors have readings that are similar to each other, it is an indication that the catalytic converter is not working as intended. If the voltage of the downstream oxygen sensor decreases, and begins to fluctuate like the upstream oxygen sensor, it means that the oxygen levels are too high and the Powertrain Control Module (PCM) will store the P0420 trouble code. This could be caused by a cracked exhaust manifold, damaged sensors or catalytic converter or electrical harness that controls the the sensors. It would be a good idea to have a professional mechanic complete an engine is misfiring inspection.