I lost my key and remote – can I program a new key myself?

ANSWER : Hello – yes, if you do not have at least 2 keys that are already "recognized" by the transceiver, you must have the new keys programmed at a Mitsubishi service center or locksmith equipped with the proper equipment. If you have 2 programmed keys which are already "recognized" by your vehicle transceiver, there is a process for adding additional "new, unprogrammed" keys, but only under those conditions.

ANSWER : Yes, you can. The ignition switch is separate from the EWS system, so replacing the switch will still allow you to use the current keys you already have. Only if you have to replace a faulty key or EWS module will you have to possibly order all new keys.

One other possibility is there is an EWS issue where the key is not being properly identified not allowing the starting sequence. This would mean ordering an EWS module or keys from the dealer. Try out all keys you have to see if any will commence in the starting sequence. If none of the keys will start the vehicle, faults should be checked to ensure there are no EWS key identification faults. If no faults are present, then most likely the ignition switch is faulty. If there are key identification faults, then it’s either a key, module, or receiver that is the issue. You may want to consult with a mechanic who has the equipment to read out the Powertrain and EWS fault memories before replacing parts.

ANSWER : Hello – unfortunately no. Modern electronic-key security systems differ from one manufacturer to the next, and each has specialized equipment for programming and setting options on remotes and electronic keys. This equipment is also not usually available to non-dealer service centers as well, for a variety of reasons. This is one case where you have to go to the dealer. Be prepared to provide documentation of ownership (title, current registration, etc.) – this is for your benefit, to prevent someone else from getting a key made for your vehicle.

ANSWER : Unfortunately, the only way to get a replacement Intelligent Access key for your vehicle is from the Ford dealer. The keys will need to be programmed with an OEM capable scan tool as well, before the vehicle will recognize them.

ANSWER : Likely, the cause of your issue is that your key was cut incorrectly. I would make sure you gave VW the correct VIN number when you had the key made. You may need to get another key made. If this does not solve your issue, I would recommend having a qualified mechanic look into your igniton. It is also likely that you will have to replace your ignition.

ANSWER : The first thing to suspect with all key fobs is the battery. Since you reused the interior or the old fob, I would first make sure the battery is installed with the positive and negative sides in the correct position. If it is, I would replace the battery to be sure. If it still doesn’t work, it will be necessary to program the fob to the car. This must be done with the DRB scan stool. The only other method requires the use of two other key fobs, which means you would be adding a new key fob.

We don’t have a pre-designed inspection that can be booked via our online platform, so I will have customer service contact you to see if there is a technician in your area with the tools and skill set to program your key fob.

Thanks, for you question!

ANSWER : Hi there. The only thing that I could think possible is causing your problem is that something may not have been correctly installed while your son was completing this maintenance. However, if your engine was difficult to start before this service, it’s possible there are different components that are damaged that simply didn’t resolve the issue. The only way of knowing what is going on with your Trailblazer would be to have one of our mobile mechanics in your area come to your location and complete a car is hard to start inspection.

ANSWER : Based on your description, I believe that the first issue is the lack of programming for your new key fob. If the dealership told you that the key requires programming and that was not done, this is the reason that the new key fob is not responsive. Next, it is possible that the key hole in your door is electronic. This means that there is a sensor on your door lock that will allow you to lock or unlock all of the doors by turning the key inside the driver front door lock. If this is the case, the fact that that part has been damaged could have caused this issue. This may not have happened immediately after the key hole was damaged, but over time the issue may have gotten worse causing the key fob problem. I would recommend having your key fob programmed by the dealership to see if that will resolve the issue because that will have to be done anyway. If this does not fix the problem, I would then recommend having the key hole replaced by a qualified professional.