Fuel Pump

ANSWER : You need to look at the theft light on dash to make sure it comes on and goes off when you turn the key to the on position. If light comes on and stays on then your theft system is causing the fuel pump to not be engaged. I recommend you check the theft system and then scan the computer for theft system codes. You may need to reprogram the keys to work or you have an bad sensor for the ignition key in the steering column.

ANSWER : Hi there – the metal component you describe is a fuel check valve on the fuel return line. Its function is to maintain a small amount of pressure in the fuel system so that starting does not require the fuel pump to run very long before the engine will start. Having replaced the fuel pump and fuel filter, I would check fuel pressure while the car is running. This is to check the fuel pump relay for burned contacts that won’t support full electrical current to the pump, and for proper fuel pressure – a malfunctioning fuel pressure regulator could also restrict power and higher speeds if pressure is too low. I would recommend an inspection of the fuel system by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hi there. There could be multiple issues causing your lack of spark problem, ranging from a minor electrical short in the main relay to an issue with your ECU. In order to know for sure, you should have a professional mobile mechanic complete an electrical problems inspection.

ANSWER : The switch you are referring to is vended with the required electrical and fuel schematic (I just looked in the box) that answers your installation question. If you want an advance view, here is a link as well. Yes, you need a return line and just refer to the aforementioned link. If you are retrofitting back to OEM, I strongly encourage you to buy the original Factory Service Manual (FSM). There are lots of details attending this system and obviously it is difficult to recount it all here. The FSM will make your life much easier and you can then make sure your installation is perfect. Alternatively, YourMechanic can dispatch a certified mechanic and perform the whole retrofit and check out if you desire. Just request and schedule a generic service such as fuel pump service and the mechanic will come to your location and estimate the parts and labor required. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Check to see if you are getting power when you test the green with orange stripe wire going to the fuel pump module. If you have no power then check the the fuel inertia switch, in the left kick panel, by the drivers foot, and see if the inertia switch is not tripped. If it is, reset it and the pump should work.

If the switch is okay then make sure it has power to it and from it, when cranking the engine. If you have no power then check the fuel relay and see if it has power to it and that it’s being turned on when you crank it. If you do not then you may have an issue with the computer not activating the fuel pump. This will require a scan of the system and in-depth tests further than the scope of what this diagnoses is capable of. You will need a wiring diagram to follow and a scanner to activate the relays to test the system.

If you decide to get this fixed, contact a certified mechanic who can perform all of these checks in order to find the root of your starting problem. Once this is done, an accurate repair can be made.

ANSWER : Hello,
You may want to try checking the fuel pump relay. The relay wires should have ground on two wires, power on one wire and switched power on another wire. To activate the fuel pump your ECU actually connects one of the ground wires to complete the circuit and send power to the fuel pump. If the wires all have power running through them, then it is likely you have a faulty relay. The wire coming from the fuel pump is the other ground wire. I would recommend having an expert from YourMechanic come to your location to diagnose your wiring as this can be very difficult and time consuming without the proper wiring diagram.

ANSWER : Hi there – I suspect you have weak power getting to the fuel pump. I would first check the voltage coming out of the fuel pump relay. If the contacts in the relay are burned, you will not get reliable current flow to the pump. Check the fuel pump ground as well (voltage drop across the ground, not just continuity). I recommend a fuel system inspection performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : This may likely be related to the fuel pressure regulator. This is a unit that helps to maintain the fuel pressure in the system. When this is not working, this may cause an erratic fluctuation in the fuel pressure or in some cases, no fuel pressure at all. If you’d like assistance with this repair, I would recommend having an expert from YourMechanic come to your location to diagnose the issue firsthand and service your fuel pressure regulator as necessary.