Why the car stalls when put on Drive?
The last week the car was stalling when braking, an oil change was perform, It was burning oil after this change, (blueish smoke when starting the car it kind of disappear after 5 to 10 minutes on road). first day after the oil change it did not stall at all, second day it did stall, tried to run it a couple of minutes, it does start but stalls when I put on Drive or R(backing).
My car has 173643 miles.
My car has an automatic transmission.
Experienced mechanics share their insights in answering this question :
This may be a sign of a faulty MAP sensor as the vehicle responds adversely to a load put on the motor (i.e. putting it in gear) as you describe. The Manifold Absolute Pressure (MAP) sensor senses engine load and generates a signal that is proportional to the amount of vacuum in the intake manifold. The engine computer then uses this information to adjust ignition timing and fuel enrichment. When the engine is working hard, intake vacuum drops as the throttle opens wide. The engine takes in more air, which requires more fuel to keep the air/fuel ratio in balance. When the computer reads a heavy load signal from the [MAP sensor]((https://www.yourmechanic.com/services/manifold-absolute-pressure-sensor-map-sensor-replacement), it adjusts the fuel mixture to slightly more rich than normal so the engine can produce more power. The computer will then retard (back off) ignition timing slightly to prevent detonation that can damage the engine and decrease performance. This may also be caused by other closely related components such as a dirty or failing mass air-flow sensor, a faulty throttle position sensor or potentially a vacuum leak.
Blue smoke coming from your exhaust generally means that the motor is burning the engine oil. This can happen for a couple of different reasons such as worn piston rings or leaking valve guide seals. When this happens, the engine oil is burned in the combustion chamber along with the fuel which is what generates the blue smoke coming from the exhaust.
I would recommend having an expert from YourMechanic come to your location to diagnose and inspect your vehicle.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
Stalling when the vehicle is put in gear simply occurs if the engine cannot accommodate the load. Among the potential causes of that are faults in engine controls. A mechanic can test the throttle position sensor and idle control valve as well as the manifold absolute pressure (MAP) sensor.
It could be a dead alternator, a bad coolant sensor or lack of fuel, just to name a few. Is your car stalling while accelerating? If so, then it could be a major vacuum leak, clogged fuel filter or a bad fuel pump. If your vehicle is stalling when driving, seek professional help to track down and fix the issue.
Fuel injectors may become dirty over time and not be able to provide as much fuel to the cylinder as is needed. Dirty fuel injectors may cause the engine to run lean which will in turn, cause hesitation when accelerating.
Most commonly when the car stalls while driving, but starts right up after, the cause is an intermittently failing crankshaft position sensor or camshaft position sensor. The first step to diagnosing this problem however, would be to scan the engine control module to check for fault codes.
If your car`s transmission has an internal pressure problem, it can cause the torque converter to lock up, causing your car to stall. Though not as often the culprit of engine stalling than others, the transmission shouldn`t be overlooked when searching for the root cause.
Automatics. Automatic vehicles use what`s called a torque converter to manage transmission fluid and keep your engine running while at a stop. If your torque converter fails, the engine can stall out.
If the engine stalls while idling or driving, the engine may be running out of fuel or not receiving enough fuel pressure to keep it running. The most likely cause of this kind of stalling would be a fuel pump that is not spinning fast enough or is intermittently cutting out.
When your engine shuts off when you slow the car down its often as a result of a: Malfunctioning transmission. Low fuel pressure, dirty or defective fuel injectors, or broken fuel pump. Bad oxygen sensor or mass flow sensor.
Bad solenoid may be causing vehicle to stall.
The most common cause of poor engine airflow is a clogged or damaged air filter. The air filter in your car protects the engine by catching all kinds of debris before it can enter the cylinder and cause more damage.
The current Nissan Altima generation first arrived in 2013. Since then, owners have complained about squealing brakes, air conditioning issues, and power steering whine. The Altima uses an electric power steering pump, and some noise can be expected when turning the steering wheel.
•
When your transmission doesn`t have enough fluid, you may experience it stalling at red lights or stop signs. Though it should start right back up, taking your car to an auto shop for repair is key as your transmission lines may be leaking and may need to be replaced.
Why does my car not accelerate when I push the gas? A car not accelerating properly can be caused by a number of things. It could be due to the throttle body, gas tank, spark plugs, or the ECU. It could also be because you have a dirty air filter or a clogged fuel filter.
Fuel pump failures can be caused by electrical faults, old age (wear) or fuel contaminants (dirt, moisture or bad gas). Fuel pump failures often occur without warning. Fuel pumps, injectors and pressure regulators are the three most commonly replaced fuel system components.
Why does my car not accelerate when I push the gas? A car not accelerating properly can be caused by a number of things. It could be due to the throttle body, gas tank, spark plugs, or the ECU. It could also be because you have a dirty air filter or a clogged fuel filter.
A failing camshaft position sensor begins losing its ability to quickly transfer data. Mismatched fuel delivery and ignition timing, even if off by a few milliseconds, will cause your vehicle to sputter, accelerate poorly, lack power, stall or even shut off.
Faulty Battery
A classic reason why your car starts for a second then dies is battery depletion. The car needs electricity from the battery to start. However, if your car starts then dies immediately, then the fault could be a lack of charging or damaged battery.
It is commonly applied to the phenomenon whereby an engine abruptly ceases operating and stops turning. It might be due to not getting enough air, energy, fuel, or electric spark, fuel starvation, a mechanical failure, or in response to a sudden increase in engine load.
Rusting, power failure, irregular pressure, missing equipment, an incorrect amount of voltage or current, dirt stuck in the system and corrosion are some of the possible reasons why a solenoid valve may not properly close or open.
The two most common issues that cause this are a bad crank or cam sensor, or a failing throttle body.
Common causes of why a car feels sluggish when accelerating include dirty mass air flow sensor (MAF), faulty spark plugs, defective throttle position sensor, clogged catalytic converter, faulty oxygen sensor, clogged air filter, and fuel system malfunctioning.
Low fuel pressure can lead to engine misfires, low acceleration, rough idles, and engine stalls. If your check engine light is on and your car has been stalling out, you may have a fuel pump failure.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The engine stalls when I put the car in reverse, but if I go past reverse into drive there is not an issue.
ANSWER : Hi there. Usually when you shift into reverse and engage the brake it will cause the engine RPM to drop; as it’s creating a load against the transmission and the engine. If the engine stalls, it may be caused by a faulty idle control valve, bad O2 sensors, or clogged fuel injectors.
In regards to the "pan", we’re not sure what you are referring, so it may be a good idea to contact one of our local professional mechanics to complete a battery inspection to determine what’s going on with your 2010 Ford Focus.
Read Full Q/A … : Why the car stalls when put on Drive?
Why the car stalls when put on Drive?
ANSWER : This may be a sign of a faulty MAP sensor as the vehicle responds adversely to a load put on the motor (i.e. putting it in gear) as you describe. The Manifold Absolute Pressure (MAP) sensor senses engine load and generates a signal that is proportional to the amount of vacuum in the intake manifold. The engine computer then uses this information to adjust ignition timing and fuel enrichment. When the engine is working hard, intake vacuum drops as the throttle opens wide. The engine takes in more air, which requires more fuel to keep the air/fuel ratio in balance. When the computer reads a heavy load signal from the [MAP sensor]((https://www.yourmechanic.com/services/manifold-absolute-pressure-sensor-map-sensor-replacement), it adjusts the fuel mixture to slightly more rich than normal so the engine can produce more power. The computer will then retard (back off) ignition timing slightly to prevent detonation that can damage the engine and decrease performance. This may also be caused by other closely related components such as a dirty or failing mass air-flow sensor, a faulty throttle position sensor or potentially a vacuum leak.
Blue smoke coming from your exhaust generally means that the motor is burning the engine oil. This can happen for a couple of different reasons such as worn piston rings or leaking valve guide seals. When this happens, the engine oil is burned in the combustion chamber along with the fuel which is what generates the blue smoke coming from the exhaust.
I would recommend having an expert from YourMechanic come to your location to diagnose and inspect your vehicle.
Read Full Q/A … : Why the car stalls when put on Drive?
Could this cause ur car to stall in warmer weather? My car never stalls during winter months. But from spring on its a neverendin
ANSWER : You should have the check engine light and engine scanned to see if the engine may be running lean due to low fuel pressures or clogged injectors. You should also have the mass airflow sensor cleaned and checked for proper readings and replace if not within specifications. The vehicle runs richer in colder weather and may be the reason for not stalling. You should clean injectors, clean throttle body and idle control valve then clean mass air sensor and relearn idle.
Read Full Q/A … : Why the car stalls when put on Drive?
I have a 2003 mini cooper and when I put it on drive it goes in neutral and back into drive.
ANSWER : Hi there. Sounds like the transmission is slipping in gear. Check the fluid level to the transmission and make sure that its full and clean. I recommend changing the transmission filter and topping it off with new fluid and retesting to see if the transmission continues to act up. If it does, then the transmission would need replaced or rebuilt. I recommend seeking out a professional, such as one from Your Mechanic, to help you with your transmission.
Read Full Q/A … : Why the car stalls when put on Drive?
Replaced alternator on car 2 times each time shows it’s charging 14v let car run for a little bit then test drive and car voltage
ANSWER : There are reports that the replacement alternators will not communicate with the engine computer and will not charge correctly. I recommend using only the manufacturer approved replacement part. It can be new or remanufactured but approved for use in the vehicle. Some lower cost alternators on the aftermarket will have charging problems since they will not communicate with the ECM on the vehicle and will stop charging.
Read Full Q/A … : Why the car stalls when put on Drive?
I put the wrong key in my car and a few weeks later my car just shut down and it will not start I believe it’s the computer but…
ANSWER : Hi there. What had happened is the wrong key set the security to the vehicle. This is to prevent the vehicle from starting with the wrong keys. Try removing the battery cables (+) and (-) for 13 minutes. During that time, put the original key in the ignition and turn it on. Activate everything in the car even though there is no power. Then remove the key and hook up the battery cables. The computer should have reset and reset the security. If the security is still being tripped, then I recommend seeking out a professional, such as one from Your Mechanic, to help you
Read Full Q/A … : Why the car stalls when put on Drive?
I filled my car up with gas, drove about a block to get a newspaper, put it in park and it died before i ever got out of the car .
ANSWER : With a car that cranks but won’t start, there are a few things that need to be checked. But before I explain them, there is a common thing that happens with Nissan’s. Every once in awhile they will flood the cylinders with fuel and wash the oil film off the cylinder walls and rings. This will reduce compression enough that the car will not start. Fortunately, there is an easy fix for this problem. It is what is known as clear flooding.
Hold the gas pedal all the way to the floor while cranking the motor. It won’t start immediately and when it does it will not run very well at first. Feather the throttle to keep it running until the motor clears out the excess fuel and the motor begins to run smoothly. If after cranking the motor with the gas pedal held to the floor for at least
Read Full Q/A … : Why the car stalls when put on Drive?
After driving awhile, when idling, RPM drops below 500 & car stalls. Happens rarely but RPM fluctuates, and drops suddenly.
ANSWER : If you are having a stalling problem then you may have a computer code stored in memory. I suggest having the computer scanned to see if there is any codes stored and diagnose them as needed. The intake hose and air filter should be inspected for leaks in the hoses and dirty or leaking air filters. If the air filter is dirty or leaking then have the mass air sensor cleaned. If you still need help, have a mechanic diagnose the stalling issue for you and let you know exactly what repairs should be done.
Read Full Q/A … : Why the car stalls when put on Drive?
