My car want start and when it do it shut down and want start until 30 minute or so. Now it want do nothing
My car is turning but it want start. Sometimes it will. And when I cut it off it want start. I'm thinking it's the fuel pump. Because I have put a starter on it and it is not the problem and a new thermostat and it still want start. My head is telling me it's the fuel pump.
My car has 237800 miles.
My car has an automatic transmission.
Experienced mechanics share their insights in answering this question :
When a car turns and won’t start, it is called a "crank no start". When this occurs, the first thing you need to do is see what is missing. All internal combustion motors need spark, fuel, injector pulse and camshaft timing to run. If one of these is missing, you have a crank no start. Diagnose the car and see what is missing.
The GM 3.8l motor has been installed in Buicks, Pontiacs and Chevrolets for decades. Particularly during the 90’s and early 00’s, these motors have used an ignition module with three coils mounted to it. This module is prone to just this type of failure. When it gets too hot, it quits working. When it cools off, it starts again. It can also display intermittent no start conditions. This is a pattern failure on this particular motor. Before I would ever replace the module, I would check for spark and injector pulse. If it just lacks spark, I would check for a crank sensor signal and replace the ignition module.
Before we get too far ahead of ourselves, do a few tests first:
Check fuel pressure. If there is none, check the fuse and the relay.
Check for injector pulse with a noid light. If this is missing, I would suspect a crank sensor. It could be a bad Power Control Module (PCM). (PCM’s are very rare to fail. I have never changed a PCM on one of these cars.)
Check for spark with a spark tester. If it is lacking spark but has injector pulse, suspect the ignition module.
If all these are present, I would take a compression test of all the cylinders. If camshaft timing is off, several of the cylinders will have significantly lower compression. Also, camshaft timing won’t start sometimes then not others; it will either start and run bad or it won’t start at all. It may sound like it is trying to start, but it won’t start.
If all of this sounds to daunting, I recommend booking a car is not starting inspection with YourMechanic
Good luck!
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
If the engine holds compression well, and the fuel system is working correctly, but it still won`t start, that tells us that your car`s spark plugs may not be working. The spark plugs ignite the air/fuel mixture inside the engine`s cylinders. It`s the resulting explosion that actually powers your car.
If the engine cranks, but the car doesn`t start: Bad fuel pump: A faulty fuel pump won`t deliver fuel to the engine, even if you`ve just filled up. Bad spark plugs: Without hot sparks to ignite the fuel charge in each cylinder, there is no combustion and no expansion of the burning mixture.
A faulty fuel rail sensor may send an inaccurate signal to the computer which may cause the engine to experience hard starting. The engine may take a few cranks longer than normal to start and in more serious cases may not start at all.
Vehicle Won`t Start or Struggles When Starting
If the fuel injector is not delivering enough fuel to the engine system, this can cause the car to struggle when trying to turn over or not turn over at all (just cranks with no result). This can also cause the engine to stall due to the air-fuel ratio not being correct.
Bad Sensors
One common culprit for this problem is the crankshaft position sensor, which measures the position and speed of the crankshaft. The computer uses the information from this sensor to know when to fire the spark plugs. If the sensor isn`t working, the spark plugs won`t fire, keeping the engine from starting.
When an engine cranks for a long time before it starts, either spark or fuel is missing or weak and each has its own reasons. Most of the time, the air / fuel mixture has been disturbed and there is too much air or not enough fuel.
When your engine cranks but won`t start or run, it could mean your engine is having trouble producing a spark, getting fuel, or creating compression. The most common causes are problems in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter).
The cranking continues, but the usual sound of the engine roaring to life doesn`t happen. If this happens to you, chances are it`s not the starter. Instead, it`s likely because your engine isn`t getting at least one of the four major components it needs to start: fuel, air, spark, or compression.
your car fails to start: the engine`s computer uses the map sensor to gauge atmospheric pressure before the engine is started. a false reading could cause too much or too little fuel to be delivered to the engine. both conditions could keep it from firing up.
Fundamentally, the engine ECU controls the injection of the fuel and, in petrol engines, the timing of the spark to ignite it. It determines the position of the engine`s internals using a Crankshaft Position Sensor so that the injectors and ignition system are activated at precisely the correct time.
A failed crankshaft positioning sensor can cause your engine tp have no spark. In most modern ICE engines they all use electronic ignition and engine management systems. Theses systems depend on the signal sent from the crankshaft position sensor to determine what cylinder is coming up on top dead center (TDC).
A Bad Crankshaft Position Sensor The crankshaft position sensor monitors the position and rotational speeds of the crankshaft. Without the crank sensor, the engine control module (ECM) wouldn`t know when to fire the fuel injectors and ignite the spark plugs.
Yes, you can drive with a bad oxygen sensor if you can still start your engine and feel little difficulty driving. But don`t leave it alone for over a couple of days, as it might cause safety problems and lead to the malfunction of other parts of your vehicle.
The primary culprits here are fouled spark plugs. Spark plug electrodes wear down over time, increasing the voltage needed to jump the gap in the plug and ignite the fuel and air mixture in the cylinder. That leads to longer cranking times before an engine fires up.
Why does my car not accelerate when I push the gas? A car not accelerating properly can be caused by a number of things. It could be due to the throttle body, gas tank, spark plugs, or the ECU. It could also be because you have a dirty air filter or a clogged fuel filter.
If there is no spark or fuel, then the first thing I would do is check the vehicle`s fuses and relays, particularly the EFI main and ignition relays. It may be possible that one of these components has failed and is cutting off power to the vehicle`s ignition and fuel systems.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My car want start and when it do it shut down and want start until 30 minute or so. Now it want do nothing
ANSWER : When a car turns and won’t start, it is called a "crank no start". When this occurs, the first thing you need to do is see what is missing. All internal combustion motors need spark, fuel, injector pulse and camshaft timing to run. If one of these is missing, you have a crank no start. Diagnose the car and see what is missing.
The GM 3.8l motor has been installed in Buicks, Pontiacs and Chevrolets for decades. Particularly during the 90’s and early 00’s, these motors have used an ignition module with three coils mounted to it. This module is prone to just this type of failure. When it gets too hot, it quits working. When it cools off, it starts again. It can also display intermittent no start conditions. This is a pattern failure on this particular motor. Before I would ever replace the module, I would check for spark and injector pulse. If it just lacks spark, I would check for a crank sensor signal and replace the ignition module.
Before we get too far ahead of ourselves, do a few tests first:
Check fuel pressure. If there is none, check the fuse and the relay.
Check for injector pulse with a noid light. If this is missing, I would suspect a crank sensor. It could be a bad Power Control Module (PCM). (PCM’s are very rare to fail. I have never changed a PCM on one of these cars.)
Check for spark with a spark tester. If it is lacking spark but has injector pulse, suspect the ignition module.
If all these are present, I would take a compression test of all the cylinders. If camshaft timing is off, several of the cylinders will have significantly lower compression. Also, camshaft timing won’t start sometimes then not others; it will either start and run bad or it won’t start at all. It may sound like it is trying to start, but it won’t start.
If all of this sounds to daunting, I recommend booking a car is not starting inspection with YourMechanic
Good luck!
My car will not start Intermittently. I purchased a new battery 2 weeks ago and yesterday the car wouldn’t start. Got a jump and
ANSWER : The issue you are having is probably due to an intermittent fault in the starter motor itself or a deficiency in the starter electrical circuit, for example a large voltage drop due to a poor ground or a high resistance connection. These issues can be readily diagnosed and resolved on a mobile basis if you request a hard starting diagnostic. If you request that diagnostic, the responding certified mechanic will get this resolved for you promptly. Based on Toyota’s Factory Service Manual, the battery should not be disconnected if the vehicle engine is running. The battery acts as a large resistive voltage sink and consequently taking the battery out of the circuit, while the alternator is still running, can create a voltage spike on the car’s electrical system which is not good for voltage sensitive components such as the engine computer. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.
car hesitates when trying to start the car ,but when started then i shut car off and start again it will start right up
ANSWER : Hi there:
Sometimes when you have problems starting an engine initially it is caused by a restriction in fuel flow; caused either by clogged fuel injectors or the throttle body that needs to be cleaned. Once the fuel starts to flow and engine warms up, it’s much easier to start. However, it could also be an air filter, EGR valve or other components that causes this issue as well, which is why it’s best to have a professional mobile mechanic complete a car is hard to start inspection so they can pinpoint the source of this issue.
2005 Chrysler 300C changed battery and alternator. Car started, ran, and then battery light came on. Shut car off and wouldn’t start.
ANSWER : Hi. There is a couple of things that could be wrong here. The battery or alternator that was just installed could be defective. Theses parts need to be tested for proper operation. There also could be a fuse, fusible link, or wiring for the battery or charging system that is blown or broken causing the battery light to come on.
The codes that you have will cause the car to shut down, run rough, or not start at all. The crankshaft sensor and camshaft sensor should be replaced. I suggest having a certified technician from YourMechanic come diagnose the charging system and check engine codes to help you proceed with correct repairs.
My car shuts off while driving and then turns back on multiple times or shuts off after driving and car turns off.
ANSWER : Hi there. Check the alternator and make sure that the wiring it connected tight. Check the battery cables and make sure that they are tight and clean. Look for any loose ground wires to the chassis on the vehicle. If everything checks out to be working correctly, then the PCM may need to be replaced as it may have a battery disconnect condition. If you need further assistance with multiple functions shutting off, then seek out a professional, such as one from Your Mechanic, to help you.
I put the wrong key in my car and a few weeks later my car just shut down and it will not start I believe it’s the computer but…
ANSWER : Hi there. What had happened is the wrong key set the security to the vehicle. This is to prevent the vehicle from starting with the wrong keys. Try removing the battery cables (+) and (-) for 13 minutes. During that time, put the original key in the ignition and turn it on. Activate everything in the car even though there is no power. Then remove the key and hook up the battery cables. The computer should have reset and reset the security. If the security is still being tripped, then I recommend seeking out a professional, such as one from Your Mechanic, to help you
97 Ford F-150 won’t start after 30 minutes of driving wait 30 minutes and start I’ll change the coil pack spark plugs wires
ANSWER : Hi There,
If I understand correctly, you have already changed the coil packs which is a good first step as this is a common indicator based upon what you are describing. Other things that you may want to also check that are subject to this kind of heat cycling are things like fuel injectors, crankshaft position sensor, camshaft position sensor, which are all subject to heat cycling failure much like the ignition coil packs are. If you need further help with diagnosing your truck, please feel free to reach out to us here at YourMechanic as we are always here to help.
Push start will not start on a 2012 Dodge Journey after hooking up subwoofers and amp car did start after hookup but never started
ANSWER : Hi there. Unfortunately, we’re unable to offer technical assistance when aftermarket components or electrical upgrades are installed, as there are simply too many different things that could be causing your ignition problem. I would recommend contacting a local audio visual installation company or local automotive shop that completes electrical repairs to get some ideas, or purchase a service and repair manual for your Dodge to review the relay schematic to determine which ones you need to check and replace. This video might help you learn how to check for damaged relays – so you might want to watch it.
