Kia Sporate Engine check light issue and car stalled this morning!

ANSWER : The infamous "loose gas cap code" is P0442. P0434 is an issue with a heated catalytic converter not coming up to temperature quickly enough. It can be caused by the fuel injection being too rich. If you starter is not turning your engine over, the issue could be a dead battery.

If you can get it jumped off, most auto parts stores will check the battery for free. They will also, time permitting, check your engine codes for free. This will help guide diagnosis for whatever else is still wrong with your vehicle.

If you need assistance with the repairs from here, I would recommend having your Check Engine Light inspected by a certified technician, like one from YourMechanic, to diagnose the problem, get an accurate assessment of damage and cost estimate for repairs. YourMechanic can dispatch a mobile, professional mechanic to your location for this repair.

ANSWER : Hello there, you have a long series of issues going on with your 2013 Hyundai Sonata. If you keep getting a repeating oil light on than there is likely a fault in that system.

Since this fault has lasted after the engine was replaced it could be a oil pressure sensor, wiring harness fault, ECU fault, oil pump, oil strainer clogged, or low oil pressure.

To diagnose this issue properly you need a complete vehicle inspection to start from square one and identify the root cause of all this.

ANSWER : This may be a result of a dirty or failing idle air control valve. The idle air control valve reads the air intake as it is mixed with fuel prior to being injected into the engine at low speeds and at idle. Since this valve is controlled by the vehicle’s computer, it will adjust idle speed based upon other measurements such as engine temperature, intake air temperature and electrical system load or voltage. When you accelerate, the engine RPM increases, and as you let off the gas, the RPM slowly returns to the normal idling speed with the help of the idle air control valve making the transition from a higher RPM back down to idle speed. When the engine RPM drops below the normal range of about ~800 RPM, this often times will cause the engine to stall indicating a dirty or faulty idle air control valve. I would recommend having an expert from YourMechanic come to your location to diagnose and replace your idle air control valve.

ANSWER : Hi there. It is possible that the battery cable came loose or the wires to the oil pressure sensor has came loose or failed. Check the battery cables and make sure that the terminals are tight and clean. Check the wires to the oil pressure sensor and make sure that they are connected and not broken. If everything looks good, then the oil pressure sensor may have failed. Plus, check the computer for codes and see what is stored. This will lead you to the part that could have failed. I recommend replacing the oil pressure sensor then checking to see if the lights will go out. If you need further assistance troubleshooting your vehicle, then seek out a technician, such as one from Your Mechanic, that can assist you with the warning lights that came on.

ANSWER : Hi and thanks for contacting Your Mechanic. If sometimes your vehicle will start with the new alternator and sometimes it won’t, then there is a loose connection in your charging system. Check all of the wires to the alternator and to the battery. Make sure that the battery cables are clean and tight. Make sure that the wires to the starter are clean and tight. A loose ground to the ignition system will cause the vehicle to not crank over. Check all of the ground wires from the battery to the starter. Make sure that they are clean and tight. If you need further assistance troubleshooting your no start situation, then seek out a technician, such as one from Your Mechanic, that can assist you.

ANSWER : Hello. If the Check Engine Light has come on, then that means the computer has detected some sort of issue. I would rescan the computer to see if the same code has returned, even after cleaning the sensor. If cleaning the MAF did not clear the code, then it is likely that the MAF sensor needs to be replaced. When changing out the MAF be sure to replace it with a high quality unit (an original equipment piece if possible), as a low quality,or low budget MAF can sometimes cause issues. Usually a MAF sensor replacement is quick, and aside from clearing the code, it can help keep the vehicle running at maximum efficiency.

ANSWER : There are countless potential causes for your illuminated check engine light. The mechanic manually turned off the light, but it came back on because the problem has not been fixed. The first place to start is retrieval of the stored diagnostic trouble codes (DTCs). These codes serve as a starting point for any further diagnostics a mechanic may perform. Codes will be stored anytime the check engine light is on. Since the first mechanic was unable to fix your concern, I recommend giving the professionals at YourMechanic a call. We offer expert check engine light diagnosis and repair.

ANSWER : The lights that you have on and the vehicle going into fail safe mode is an indication you have a major system failure that will require computer to be tested for codes first. There are many possible codes it can be so the additional testing will be needed to isolate the cause of the problem.