How long should my brake pads last

ANSWER : I would suggest trying to disconnect and reconnect the wiring to the rear lights. I have seen these older Toyota vehicles rear lighting short out on the lights themselves due to the way the light circuit was made on the lamp housing. Look at the housing circuit on the light to see if one is touching another, and that could tell you why it is malfunctioning. There could also be a problem with the brake light switch. If you are not comfortable dealing with wires, I recommend getting in touch with a certified mechanic who can look at your brake light issue for you to see what’s going on.

ANSWER : The brake pedal is working to stop the vehicle, but there may be air in the controller unit causing the ABS brakes to not function. I recommend bleeding the brake system from the farthest location from the master cylinder to the master cylinder including the ABS unit. If the brakes are still spongy after a full bleed, then the controller will need to be replaced. If you need further assistance with your brake pedal being spongy, then seek out a professional, such as one from Your Mechanic, to help you.

ANSWER : It’s possible to have someone alter the brake pedal or adapt a brake pedal from a different vehicle. You may call around to some customization shops to see if anyone is interested in taking on the project. But first, I would try reaching out to the selling dealer with your concern – especially since it is a new model. Good luck.

ANSWER : Hi there. The first thing that pops in my mind beyond of what you have listed is perhaps the electrical harness attached to the brake switch. Perhaps the harness itself is damaged or you have an exposed wire, loose ground wire somewhere. You might want to have a professional mobile mechanic come to your location and complete a brake lights not working inspection to help you diagnose this issue.

ANSWER : This is definitely not normal and should be looked at more closely to get a second opinion. You are correct that your brake pads should last at least 25,000 miles or more in some cases. It all depends on the type of car and driving habits of the owner. It may be possible that your pads have been hung up on the brake rotors, causing them to drag against the rotors constantly, wearing them down much faster. However this is usually very noticeable when you’re driving and may have cased other issues with the rotors in the process. I would recommend having an expert from YourMechanic come to your location to inspect your brakes to determine why they’re wearing so quickly.

ANSWER : Hello. If the brake pedal is going to the floor then that means that it is not building pressure. If the brake system has been fully bled and there is no air in it then most of the time it is a bad master cylinder or it can be caused by a bad ABS module. If the brake fluid was low and if air got into the system then the only way to properly bleed it is with a scan tool that would allow you to open and close the valves in the ABS unit. Air gets trapped in these easily if the brake fluid gets low. This can also explain why the brakes are locking up. I would usually use my scan tool to bleed the system out first before going any further. I would also scan the brake control module to see what it is reading as a fault. If there is no air in the system and if there is no prominent code then I would replace the master cylinder first. If you want to check out why your brakes are locking up, consider YourMechanic, as a certified mechanic can come to your home or office to diagnose and repair this.

ANSWER : Hello, thank you for writing in. These situations are understandably questionable. The service providers at a lot of common oil changing and tire repair centers will quote you for a variety of things that can be updated. This does not always mean you are in dire need for more repairs. If braking seems to be harder, spongy, or takes longer, then you have reason to be concerned. Otherwise, you should check the amount of brake pad material left on the calipers. This can be visually inspected without too much trouble. Remove the wheel and physically measure the amount left, compare them to your vehicle specifications. It is a little early to worry about brake fluid or the rotors. However if the brake fluid is low, the rotors are warped from a hard stop, or there are obvious issues you should look into the system further. Only further inspection will confirm or deny the recommendations. For a second inspection, contact our service department to schedule an appointment.

ANSWER : Hi, thanks for writing in. You need to check the brake switch install adjustment. You may have the switch adjusted too tight and it is holding the the brake pedal partly down. This will cause the brake master cylinder to not release the brakes when you let off the pedal. Readjust the switch away from the pedal until you feel some free play again in the pedal. This should fix the problem. If you would like help, consider having an expert automotive technician from YourMechanic come to your home or office to inspect and diagnose this issue for you, and make or suggest any repairs as needed.