Engine modification

ANSWER : Anything is possible with enough engineering. The changes you are looking at would take major structural changes and would definitely not be an easy job. You could possibly consult a manufacturing engineer to get more details on how this could actually be carried out and whether it would be feasible.

ANSWER : If you swapped the engine from a vehicle that is 4 years newer than the car is then you are going to have electrical and sensor incompatibilities that may not be able to be fixed by just a few sensor replacements. There were many changes in computer and emission related items between 2010 and 2014 engines. I would recommend having a mechanic like one from YourMechanic come to you and compare the two engines to isolate the possible differences and see if the problem can be fixed.

ANSWER : Hi there. From the description you have provided, I’m am inclined to agree with your assessment of a used engine being installed in your vehicle. An inspection of the engine, by a qualified technician could determine whether the engine is sound. The Check Engine Light on and having a TPS (throttle position sensor) code does not necessarily mean the sensor is at fault. Circuit tests should be performed to confirm the fault. The likelihood of the ECM (electronic control module/computer) giving you all the codes at once is remote. Other component failures could occur. Address those as they come up. Even though you already made the purchase, I recommend having your vehicle inspected by a certified technician so that you can get a thorough evaluation of the car’s true condition.

ANSWER : Hi there. There are a lot of things that can cause this on your 2012 BMW M5. I usually start by scanning the computer for codes to see what comes up. If there are not codes then I load test the alternator and the battery to see if they are failing. Low voltage in the electrical system will cause this. If that is fine, then it is usually caused by a failing throttle body. I have seen a lot of these fail due to the motors in them hanging up. If the problem is only happening intermittently, this can make the issue hard to duplicate, but you can still have tests done on the car. If you are going to have this fixed, consider YourMechanic, as a certified mechanic can come to your home or office to test the vehicle and diagnose the Engine Malfunction Light.

ANSWER : Hi…thank you for your questions. If required in the application, a portable engine support bar is used to support an engine during mount replacement. The support bar has lifting capability as well so that the mount can be unloaded and removed. If a particular repair application requires a "crane" (complete engine removal for instance), such are portable these days in any event. With regard to the exhaust system repair, mechanics use ramps to gain access. Six ton portable jack stands will safely support a car two feet into the air which provides more than enough access to repair or replace any exhaust system component. If you desire replacement of the mounts, please refer to YourMechanic’s motor mount replacement service page. For exhaust leaks, please use the exhaust system inspection/repair page page. Once on each of those service pages, if you click on "Get a Quote" and enter your vehicle information (year, make, model) you can obtain cost info and schedule the service. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Hello there, you have a long series of issues going on with your 2013 Hyundai Sonata. If you keep getting a repeating oil light on than there is likely a fault in that system.

Since this fault has lasted after the engine was replaced it could be a oil pressure sensor, wiring harness fault, ECU fault, oil pump, oil strainer clogged, or low oil pressure.

To diagnose this issue properly you need a complete vehicle inspection to start from square one and identify the root cause of all this.

ANSWER : Hi there. Most of the time, reduced engine power is caused by a restriction of fuel, or the throttle body’s inability to efficiently mix air and fuel. This could be caused by a failing mass air flow sensor, EGR valve or other fuel system components. Since the check engine light is on, you should have a professional mechanic complete an inspection at your location to determine what codes are stored and which components require repair. This should resolve your issue.

ANSWER : Hi there. I think it may be a good idea to find a new mechanic. Fortunately, our mobile mechanics are able to complete most diagnostic inspections and complete a lot of repairs services at your location, and on your schedule. In what you are describing above, the current issue seems to be with your EVAP system, which is designed to relieve pressure in the fuel tank and also collect harmful vapors before they escape into the air. Now, in regards to the car "blowing up"; that’s a bit dramatic, but it is important to have your issues repaired if it’s related to the EVAP system. Here is what I would recommend. Set up an appointment to have one of our mobile mechanics come to your location to complete a check engine light inspection – (click here to set up an appointment). This will allow them to download the stored error codes that cause the light to illuminate and determine what parts need repair or replacement. Then, they’ll be better prepared to provide you with a repair estimate and complete the repairs in most cases for you.