Check engine light is on and the car does not want to drive

ANSWER : Hi there:

On most modern cars, there are a series of sensors that are designed to monitor mechanical systems; such as the transmission on your Saturn. In most cases, when a problem occurs, a trouble code is stored in the on board computer that will indicate what is causing the troubles. The best way to find out what’s going on is to not take your car to a shop; let the mechanic come to you. Contact one of our professional mobile mechanics to complete a check engine light inspection first. This will allow them diagnose what’s wrong with your car so they can recommend and complete the right repairs.

ANSWER : Hi there. It is possible that the battery cable came loose or the wires to the oil pressure sensor has came loose or failed. Check the battery cables and make sure that the terminals are tight and clean. Check the wires to the oil pressure sensor and make sure that they are connected and not broken. If everything looks good, then the oil pressure sensor may have failed. Plus, check the computer for codes and see what is stored. This will lead you to the part that could have failed. I recommend replacing the oil pressure sensor then checking to see if the lights will go out. If you need further assistance troubleshooting your vehicle, then seek out a technician, such as one from Your Mechanic, that can assist you with the warning lights that came on.

ANSWER : Hello there, you have a long series of issues going on with your 2013 Hyundai Sonata. If you keep getting a repeating oil light on than there is likely a fault in that system.

Since this fault has lasted after the engine was replaced it could be a oil pressure sensor, wiring harness fault, ECU fault, oil pump, oil strainer clogged, or low oil pressure.

To diagnose this issue properly you need a complete vehicle inspection to start from square one and identify the root cause of all this.

ANSWER : Hello, thank you for writing in. Shaking and vibrating typically comes from a misfire, or poor engine performance. A lack of oil will absolutely contribute to these symptoms and amplify them, if not cause them to begin with. You want to turn your attention to the cause of the oil leak. If external (you can see the leaking oil), then you will want to trace the leak to the component which has failed. If the leak is internal (or the engine is consuming oil), the leak will be harder to find. It will also explain the poor engine performance due to excess oil in the combustion chamber. A head gasket is one of the main components that will fail and cause these issues. It is however not common for a vehicle this age to have these kinds of problems. You will also want to scan the computer, and see what codes are triggering your check engine light. These diagnostic tools will help you determine what system(s) is to blame for the malfunction. For more diagnostic help, contact our service department to schedule an appointment.

ANSWER : Anything is possible with enough engineering. The changes you are looking at would take major structural changes and would definitely not be an easy job. You could possibly consult a manufacturing engineer to get more details on how this could actually be carried out and whether it would be feasible.

ANSWER : There are countless potential causes for your illuminated check engine light. The mechanic manually turned off the light, but it came back on because the problem has not been fixed. The first place to start is retrieval of the stored diagnostic trouble codes (DTCs). These codes serve as a starting point for any further diagnostics a mechanic may perform. Codes will be stored anytime the check engine light is on. Since the first mechanic was unable to fix your concern, I recommend giving the professionals at YourMechanic a call. We offer expert check engine light diagnosis and repair.

ANSWER : It is possible that you could be having an issue with your powertrain control module. This is somewhat of a common problem on many GM vehicles. I would recommend having your vehicle inspected by the dealership to determine if the powertrain control module is functioning properly. If not, a reflash of the powertrain control module may resolve the issue but often times it must be replaced.

ANSWER : This may be a result of a dirty or failing idle air control valve. The idle air control valve reads the air intake as it is mixed with fuel prior to being injected into the engine at low speeds and at idle. Since this valve is controlled by the vehicle’s computer, it will adjust idle speed based upon other measurements such as engine temperature, intake air temperature and electrical system load or voltage. When you accelerate, the engine RPM increases, and as you let off the gas, the RPM slowly returns to the normal idling speed with the help of the idle air control valve making the transition from a higher RPM back down to idle speed. When the engine RPM drops below the normal range of about ~800 RPM, this often times will cause the engine to stall indicating a dirty or faulty idle air control valve. I would recommend having an expert from YourMechanic come to your location to diagnose and replace your idle air control valve.