Why the brake light is on after the brakes pads and roller are replaced with new parts?
Already listed above
My car has 289000 miles.
My car has an automatic transmission.
Experienced mechanics share their insights in answering this question :
Hi there. Check the wheel speed sensors and see if they are plugged in. If the wheel speed sensors are plugged in, then remove the sensors and clean it off. Then put them back in and drive the vehicle. The light should go out if the sensors are responding to the brakes system. When the new rotors are put on, check to see if the reluctor wheel is still in place and not bent, which will cause the computer to not register the ABS wheel speed sensors. If you need further assistance with your brakes system, then seek out a professional, such as one from Your Mechanic, to help you.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
When the ECU senses an abnormal speed given specific conditions, it engages the ABS or traction control as needed to control the vehicle properly and safely. In your case these sensors may have been bumped or need to be reset due to the movement when the brakes were replaced.
Bad Switch: One common reason for the Parking Brake light to stay on is a failing or failed switch. This can be checked easily by jiggling the handle after it is down. If the light turns off (or turns off and then back on), the switch is the most likely culprit and will need to be replaced.
When brakes are new, the sensor wire is positioned near the backing plate of the pad. As the pad wears down to the sensor wire, the sensor wire touches the brake rotor and electrically triggers the brake warning light circuit.
First things first: What is the function of the brake light? This, as with so many lights on your dashboard, is a warning indicator. It may have detected that your brake system is malfunctioning or your brake fluid level is low.
Four Reasons Your Anti-lock Brake System Light Can Come On
The four common reasons that typically cause this light to turn on include a malfunctioning ABS module, low levels in the fluid reservoir, broken wheel speed sensors, or the system is turned off.
When your brake light comes on, your car is letting you know that either your vehicle is low on brake fluid, the emergency brake is activated, there`s trouble within the ABS unit, or there`s a problem with the sensors.
If the dashboard light remains on, it`s telling you that thre is a brake system problem that could prevent you from stopping your vehicle. Turn off the engine and arrange to have the vehicle transported to your trusted mechanic.
A sensor in the master cylinder monitors the brake fluid level in the system. If the fluid levels are below the minimum threshold, the sensor will trigger the brake light to illuminate.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
EPC light on 2004 Jetta. Code said brake switch faulty, but brakes lights worked. Replaced brake switch, now no brake lights.
ANSWER : Hi there. The first thing that pops in my mind beyond of what you have listed is perhaps the electrical harness attached to the brake switch. Perhaps the harness itself is damaged or you have an exposed wire, loose ground wire somewhere. You might want to have a professional mobile mechanic come to your location and complete a brake lights not working inspection to help you diagnose this issue.
Brake lights are not working. replaced brake light swtch still no brake lights. the third brake light the connection was melted at
ANSWER : The first thing to do is to repair third brake light and replace the brake light fuse and then see if the third brake lights work and the lower lights start working? If only the 3rd brake light starts working then you may need a further checks on the turn signal flasher or switch could be bad.
When I put my foot on the brake my back left brake light goes off, when I take it off the brake the brake light comes on
ANSWER : I would suggest trying to disconnect and reconnect the wiring to the rear lights. I have seen these older Toyota vehicles rear lighting short out on the lights themselves due to the way the light circuit was made on the lamp housing. Look at the housing circuit on the light to see if one is touching another, and that could tell you why it is malfunctioning. There could also be a problem with the brake light switch. If you are not comfortable dealing with wires, I recommend getting in touch with a certified mechanic who can look at your brake light issue for you to see what’s going on.
I replaced the brake light switch. Gear lever unlocked because it had locked. Now the brakes feel hard.
ANSWER : Hi, thanks for writing in. You need to check the brake switch install adjustment. You may have the switch adjusted too tight and it is holding the the brake pedal partly down. This will cause the brake master cylinder to not release the brakes when you let off the pedal. Readjust the switch away from the pedal until you feel some free play again in the pedal. This should fix the problem. If you would like help, consider having an expert automotive technician from YourMechanic come to your home or office to inspect and diagnose this issue for you, and make or suggest any repairs as needed.
abs light on brake line broke have been replace I bleed brake line but brake pad still go to the floor now wheels lock up
ANSWER : Hello. If the brake pedal is going to the floor then that means that it is not building pressure. If the brake system has been fully bled and there is no air in it then most of the time it is a bad master cylinder or it can be caused by a bad ABS module. If the brake fluid was low and if air got into the system then the only way to properly bleed it is with a scan tool that would allow you to open and close the valves in the ABS unit. Air gets trapped in these easily if the brake fluid gets low. This can also explain why the brakes are locking up. I would usually use my scan tool to bleed the system out first before going any further. I would also scan the brake control module to see what it is reading as a fault. If there is no air in the system and if there is no prominent code then I would replace the master cylinder first. If you want to check out why your brakes are locking up, consider YourMechanic, as a certified mechanic can come to your home or office to diagnose and repair this.
Abs light, emergency brake light, steering wheel assist light, engine light, EPC light, traction control light
ANSWER : Hello, thank you for writing in. The vehicle does utilize a lot of the same sensors for these systems. Are there any other codes that are coming up when this code appears? If so you will want to take these into consideration when processing the repair and making a diagnosis. The module may be bad, and replacing it should fix the problem. The lights should turn off once the main computer recognizes the new module and the sensors sync up. If you believe the sensors need to be cleaned you may do so. Do as minimal as possible to make sure you are not damaging the sensor or disrupting the wiring inside. A bad connection would make the lights stay on. With so many lights that are effected by the module being illuminated, the module is likely bad or does not have a connection. Check the connection first and then resort to replacing the unit. For more help with these electrical tests, contact our service department.
Brake light and abs light on, my brakes are soft ( needs to be replaced ) if I replace brakes will both lights go off?
ANSWER : A soft brake pedal generally indicates a hydraulic issue with the brake system. If the hydraulic system has a leak or a faulty seal in components such as the brake master cylinder of ABS pump, the brake system will not operate with the correct pressure. Worn brake pads may make the brake pedal travel farther than say new brake pads, but this generally does not cause a "soft" brake pedal. Replacing brake pads may not turn the ABS and BRAKE lights off. An abs system inspection should be performed by a certified technician before replacing any parts that may or may not correct your issue. I cannot predict if you will have a further issue but as far as is it unsafe ? Yes, driving with a possible hydraulic fault with the brake system is very unsafe as the brakes may fail entirely.
No dash lights, back right tail light is out, no parking lights. Brake lights work though as does head lights.
ANSWER : Hi there. In many cases, when you have electrical problems like you’re describing, it’s caused by multiple electrical component failure. It’s likely that a few electrical relays are not working; especially if you have systems that utilize the same components (such as your brake light and tail lights). I would recommend having a professional mobile mechanic come to your location to complete an electrical problems inspection first, so they can pinpoint what is damaged and recommend the right repairs.
