Opinion on aftermarket oil catch cans

ANSWER : The fuel pump will not stay on if you loose oil pressure. This is why it is shutting off. The loss of oil pressure may be from bad crankshaft bearings or camshaft bearings. The engine oil pan should be removed and the oil pump needs to be checked to ensure that you put in the pick up tube seal to the pump and connected the pump to the block. Then remove at least one main bearing cap and inspect the bearings for excessive wear and crankshaft damage. If you need some help with this, consider YourMechanic, as a certified technician can help diagnose the issue with your oil pressure firsthand and help you fix it accordingly.

ANSWER : It’s a great idea if you’ve got a GDI, gasoline direct injection, because it’s going to keep any oil from getting into the engine and getting clogged up with carbon. If you’ve got an older car that’s worn and uses some oil, it’s a very good idea. Just make sure you get one that’s made for your car.

ANSWER : Hi there, thanks for writing in. The valve stem seals are the most common cause of this on your engine. When they fail, it requires that the cylinder heads be removed and rebuilt to fix it. The piston rings can also cause this but they are not as common. Unfortunately there is not anything, not even heavier oil that will fix this. You will need to have the heads rebuilt.

ANSWER : You might have a problem with the oil filter leaking when you rev the engine and increase the oil pressure. This can be from a collapsed oil filter media or excessive oil pressure from the engine. I recommend having the oil and filter replaced using a good quality filter and have the oil leak verified to be from the filter. Make sure to not run the engine low on oil. If you are finding you do not want to drive with the leak, a mobile technician from YourMechanic can come to your home or office, and replace both your filter, and oil.

ANSWER : Hi There,
It sounds like you may need to replace the oil cap o-ring. If you haven’t done this before there are two O-rings to replace; a small green one on the base of the filter cap stem and the large black one that seals the filter cap (which seems to be the one you are having issues with). The large O-ring sits in a small square-shaped groove that is at the base of the oil filter cap. It is very easy to not properly seat the large O-ring because the threads for the oil cap are quite large and will accept the O-ring if you are not careful. I would suggest having a professional from YourMechanic come to your location to take a look at your vehicle.

ANSWER : Most older cars have oil leaks. Sealing technology has just not kept up with mechanical improvements to engines so much so that leaks often kill engines rather than mechanical problems. So, it is not unexpected at all to have an, indeed many, oil leaks on a 23 year old car. Oil leaks vary hugely in terms of severity and priority of repair. Oil leaking onto a hot engine manifold is the worst case (the oil can start a fire; at best, you are left breathing oil fumes in the cabin, as the oil burns off of the manifold) while de minimus seepage of oil at the oil drain plug or oil pan gasket, while annoying and messy, if limited enough is not an emergency. Some leaks are easy to repair, while others literally require the engine to be removed just to get physical access to all the leak points. In your circumstance, if you smell burning oil, oil is probably leaking onto a hot engine part such as the exhaust manifold. A certified Mechanic, dispatched by YourMechanic right to your location, can perform an oil leak diagnostic and then let you know of your repair options and costs.

As far as the check engine light, that is not related to the oil leak(s). If you request a check engine light diagnostic, a certified mechanic from YourMechanic would use a code scanner to retrieve the specific diagnostic trouble code(s) from your car’s PCM that have caused the check engine light to illuminate. Using those codes, the appropriate individual vehicle components or sub-systems (often a sensor, circuit, and the like) are then carefully tested, based on specifications set forth in your car’s Factory Service Manual, to pinpoint the cause of the fault or the reason why the check engine light has illuminated. Once the faulty part or component is identified, it is explained to your satisfaction and the mechanic will let you know of the cost to repair. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Unless there is an imperfection (e.g., serious pitting or irregularities) on the engine mounting base for the filter gasket, the leak is probably not at the filter. There are other adjacent potential leak spots such as the oil pan gasket, oil pressure sending unit and so forth. If the leak is significant at all, merely thoroughly cleaning the suspect area and running the engine while looking for the leak should be sufficient. If you still can’t find the leak origin, a UV visible dye can be added to the engine oil which will then make the leak point visible using a detection light. If you want these steps performed by a certified Mechanic, dispatched by YourMechanic right to your location, please request an oil leak diagnostic and the responding certified mechanic will get this taken care of for you. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : This light will usually come on when one of two things are happening. Either the motor is in fact low on oil or the oil pressure sending unit is not working properly and may be producing a faulty reading. I would recommend first, to check the actual oil level in the motor by using the dipstick. Be sure the oil level reaches the "full" mark. If this registers as "full" then you likely have a faulty oil pressure sending unit. I would recommend having an expert from YourMechanic come to your location to take a look at your vehicle to determine what may be causing your low oil pressure light to come on.