Car won’t start – 2004 Mercedes Benz C240

ANSWER : The issue you are having is probably due to an intermittent fault in the starter motor itself or a deficiency in the starter electrical circuit, for example a large voltage drop due to a poor ground or a high resistance connection. These issues can be readily diagnosed and resolved on a mobile basis if you request a hard starting diagnostic. If you request that diagnostic, the responding certified mechanic will get this resolved for you promptly. Based on Toyota’s Factory Service Manual, the battery should not be disconnected if the vehicle engine is running. The battery acts as a large resistive voltage sink and consequently taking the battery out of the circuit, while the alternator is still running, can create a voltage spike on the car’s electrical system which is not good for voltage sensitive components such as the engine computer. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : Hi there. This does sound like an issue with the wiring. If the check engine light is coming on every now and then this means that when it does not come on there is no power to the computer. This can be the wiring harness issue or an ignition switch problem. I would have to test for voltage to the computer when the problem is occurring to be able to find where the issue lies. If you need assistance, a certified YourMechanic technician can be dispatched to your location to inspect your vehicle’s non-start issue and suggest any necessary repairs.

ANSWER : Hi and thanks for contacting Your Mechanic. If sometimes your vehicle will start with the new alternator and sometimes it won’t, then there is a loose connection in your charging system. Check all of the wires to the alternator and to the battery. Make sure that the battery cables are clean and tight. Make sure that the wires to the starter are clean and tight. A loose ground to the ignition system will cause the vehicle to not crank over. Check all of the ground wires from the battery to the starter. Make sure that they are clean and tight. If you need further assistance troubleshooting your no start situation, then seek out a technician, such as one from Your Mechanic, that can assist you.

ANSWER : Your MAP sensor is an important input for your computer. It helps determine the load on the engine to calculate the correct amount of fuel to inject. It sometimes takes a few seconds for the vehicle to realize that the sensor is not producing a good signal.

At that point, it will use other methods to determine the fuel rate, such as pre-programmed fuel maps, throttle position, etc. I would suggest replacing the MAP sensor and retesting. If you would like to have it checked first, a certified technician from YourMechanic will be able to scan your vehicle and test components to determine the root cause of your starting issue before making a repair.

ANSWER : Hi there. There are a number of issues that will make a car hard to start. Everything from the electrical system to the fuel system to the actual starter itself can be the problem. Finding the root cause of a hard starting engine can take some investigation. Ignoring a hard starting issue can further damage the vehicle, which will often result in a more expensive repair. You might want to have a mobile mechanic complete a car is hard to start inspection so they can pinpoint the source of the issues you’re having and recommend the right repairs be completed.

ANSWER : Hi there. It sounds like you have a failed starter. However, without proper testing there is no way to be 100% sure. I suggest having the battery tested first with a digital battery tester that provides current voltage, cold cranking amps, and state of health. Also inspect for corrosion on the terminals and cables as this will cause excessive resistance and not allow proper voltage/amps to the starter. Other possible failures could be in the wiring harness, relay, fuses, or communication network. I suggest having a qualified technician perform an inspection to avoid replacing unnecessary parts. Your Mechanic has several available technicians that can assist you with a car does not start inspection.

ANSWER : Hello, thank you for writing in. It is difficult to determine the issue without some more information. To start, when the check engine light illuminates, you want to scan the vehicle for diagnostic codes. These are what set the check engine light off, and are meant to tell the driver what the computer has detected is wrong. Codes can be pulled at most automotive parts stores, and by most technicians. Once you have that information you can focus in on one component or system. If the engine is truly overheating, then you want to start by checking your coolant and fluid levels. For more help with diagnosing and resolving the issue, contact our service department to schedule an appointment.

ANSWER : Hi there:

Sometimes when you have problems starting an engine initially it is caused by a restriction in fuel flow; caused either by clogged fuel injectors or the throttle body that needs to be cleaned. Once the fuel starts to flow and engine warms up, it’s much easier to start. However, it could also be an air filter, EGR valve or other components that causes this issue as well, which is why it’s best to have a professional mobile mechanic complete a car is hard to start inspection so they can pinpoint the source of this issue.