BMW oil light reset
I have a BMW 2010 535xi and a code came up which it won't let the car start it says oil level sufficent to start engine how do I reset so the car will start
My car has 100000 miles.
My car has an automatic transmission.
Experienced mechanics share their insights in answering this question :
Hi There,
This is an indicator that usually comes up when you have an oil change. Try the following, which should allow you to reset and start the vehicle:
Step 1
Insert key into slot
Step 2
Press start/stop button without depressing clutch/brake and wait for the service reminder to disappear.
Step 3
Immediately after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear. Keep the odometer button pressed and after another 2-3 seconds the oil can light will appear. Do not hold for longer than necessary as it will try to restart the process in some cases.
Step 4
You are now in the service menu, use the toggle switch on indicator stalk to scroll up/down through the various service items.
Step 5
When you have the item you want to reset showing, press the BC button on end of indicator stalk. Reset should now appear in the display. Press in and hold the BC button for 2-3 seconds and a clock will start whirling around and hey presto, its done
Step 6
You can now either scroll up/down to select another item (as in step 4) or you can press the start/stop button to exit.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
Step 1 – Start the engine. Step 2 – If a service is due the display will show “Service required”. To reset this message, locate and press the OK button located at the top right of the steering wheel for more than 1 second. Step 3 – The service interval will be reset to the default setting.
Press and hold the small odometer button near the bottom left corner of the instrument panel until the service message appears. Release the button, and press and hold it again until the message says “Reset?”. Release the button again, and press and hold it. The message will say, “Reset in Progress”.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Check engine light and oil light comes on before oil change?
ANSWER : Hi There,
As you may know, these lights are designed to come on at specific mileage intervals that are preset by the factory. When your mileage exceeds a certain amount relative to the last oil change, this will trigger the lights to come on. Typically this will include the oil light and the check engine light as there are also other basic service items that are checked during oil changes. I would recommend obtaining an owner’s manual for your car if you do not already have one. This will usually indicate the specific service intervals and recommended maintenance items for your vehicle at the various mileage intervals.
The tire pressure monitor will also come on when the air pressure in the tires has reached a specific threshold relative to the tire design specification. Tire pressure is also impacted by the outside air temperature. For every 10° drop in air temperature outside your tires will lose about 1% in PSI or inflation. As you may know, as the temperature of the air changes the density of the air changes as well causing the tire pressure to be impacted by this. When this happens, the sensors in the wheels will detect this change in tire pressure and cause the tire pressure light to come on. Aside from replacing faulty tire pressure sensors, another way to help prevent this type of fluctuation in tire pressure is by the use of Nitrogen in your tires rather than regular air. As you may know, air is approximately 78% Nitrogen, 21% Oxygen and the rest is water vapor and some other small concentrations of gases. Nitrogen is much less likely to migrate through tire rubber than oxygen. This will maintain your tire pressure much more consistently during large temperature fluctuations.
Low oil pressure light comes on when idle. Check engine light is on as well. Both came on after getting an oil change 3 days ago.
ANSWER : It is possible that they put in the wrong viscosity oil. In rare instances, a defective filter will also cause low pressure. If there is too much oil, it will aerate and cause low pressure. Be sure the oil level is really not above "max". The P2187 code will appear if the oil fill cap is not tight but it will also appear due to a myriad of causes because that code only "generally" identifies a lean running condition. Consequently, numerous parts would have to be tested including the O2 sensor, gas cap seal, manifold air leaks, any vacuum leak anywhere including PCV and EVAP systems, exhaust leaks, and fuel system faults such as failing fuel pump, clogged filter and more. Since the car has relatively low mileage, you would not expect a failed oil pump, although the pressure sensor (or switch) could be bad. However, the occurrence of the oil pressure warning light is quite coincidental to the oil change, thus I would suggest bringing the car back and asking them to redo with a new filter and double check the viscosity of the new oil that they use. If the problem persists after that, you will have to test actual operating oil pressure (at idle for instance) as well as the oil pressure switch. Finally, if the oil pressure warning light comes on continuously, unless the warning circuit itself is malfunctioning, that means the oil pressure is too low to operate the engine without damaging it. Anytime the light comes on for more than literally an instant, you should shut down the car and thus an issue like this obviously has to be repaired.
If you’d like, a YourMechanic certified mechanic can come to your home or place of business to inspect the vehicle and perform an oil pressure light is on inspection to diagnose the vehicle and suggest potential repairs.
lost all oil pressure, replaced the oil pump, low oil sensor, oil pressure sensor, oil pan gasket,
ANSWER : The fuel pump will not stay on if you loose oil pressure. This is why it is shutting off. The loss of oil pressure may be from bad crankshaft bearings or camshaft bearings. The engine oil pan should be removed and the oil pump needs to be checked to ensure that you put in the pick up tube seal to the pump and connected the pump to the block. Then remove at least one main bearing cap and inspect the bearings for excessive wear and crankshaft damage. If you need some help with this, consider YourMechanic, as a certified technician can help diagnose the issue with your oil pressure firsthand and help you fix it accordingly.
Oil consumption. Burning oil. Oil light turns up on idle.
ANSWER : Hi there, thanks for writing in. The valve stem seals are the most common cause of this on your engine. When they fail, it requires that the cylinder heads be removed and rebuilt to fix it. The piston rings can also cause this but they are not as common. Unfortunately there is not anything, not even heavier oil that will fix this. You will need to have the heads rebuilt.
Hello Ben, my oil pressure is came on. Slight oil drip. Mechanic changed oil, replaced sending unit. Light came on after a day.
ANSWER : You need to have the oil pressure checked to see if the oil pressure is within specifications before you condemn the engine internal problem with oil pump or crankshaft and bearings. You may want to get the dealer involved now and let them take care of getting the light diagnosed.
Abs light, emergency brake light, steering wheel assist light, engine light, EPC light, traction control light
ANSWER : Hello, thank you for writing in. The vehicle does utilize a lot of the same sensors for these systems. Are there any other codes that are coming up when this code appears? If so you will want to take these into consideration when processing the repair and making a diagnosis. The module may be bad, and replacing it should fix the problem. The lights should turn off once the main computer recognizes the new module and the sensors sync up. If you believe the sensors need to be cleaned you may do so. Do as minimal as possible to make sure you are not damaging the sensor or disrupting the wiring inside. A bad connection would make the lights stay on. With so many lights that are effected by the module being illuminated, the module is likely bad or does not have a connection. Check the connection first and then resort to replacing the unit. For more help with these electrical tests, contact our service department.
No dash lights, back right tail light is out, no parking lights. Brake lights work though as does head lights.
ANSWER : Hi there. In many cases, when you have electrical problems like you’re describing, it’s caused by multiple electrical component failure. It’s likely that a few electrical relays are not working; especially if you have systems that utilize the same components (such as your brake light and tail lights). I would recommend having a professional mobile mechanic come to your location to complete an electrical problems inspection first, so they can pinpoint what is damaged and recommend the right repairs.
think i put wrong oil in car went few miles lose power car dies oil in spark plugs still starts low oil blinking light before die.
ANSWER : Hello. If you put too thick of an oil in the car, then you may have damaged the engine bearings but this should not have caused oil to get in to the spark plugs unless the oil got into the intake of the engine or one of the pistons rings broke. If you ran it without oil and then tried to put oil in thinking it would be okay after that, then you were not that lucky and broke or damaged all of the rings on the pistons. If you would like to have this looked over, a certified professional from YourMechanic can come to your car’s location to inspect the stalling issue and go over all of the relevant systems for a better diagnosis.
