Abs and brake light on

ANSWER : I would suggest trying to disconnect and reconnect the wiring to the rear lights. I have seen these older Toyota vehicles rear lighting short out on the lights themselves due to the way the light circuit was made on the lamp housing. Look at the housing circuit on the light to see if one is touching another, and that could tell you why it is malfunctioning. There could also be a problem with the brake light switch. If you are not comfortable dealing with wires, I recommend getting in touch with a certified mechanic who can look at your brake light issue for you to see what’s going on.

ANSWER : Hi there. The first thing that pops in my mind beyond of what you have listed is perhaps the electrical harness attached to the brake switch. Perhaps the harness itself is damaged or you have an exposed wire, loose ground wire somewhere. You might want to have a professional mobile mechanic come to your location and complete a brake lights not working inspection to help you diagnose this issue.

ANSWER : Hello, thank you for writing in. The vehicle does utilize a lot of the same sensors for these systems. Are there any other codes that are coming up when this code appears? If so you will want to take these into consideration when processing the repair and making a diagnosis. The module may be bad, and replacing it should fix the problem. The lights should turn off once the main computer recognizes the new module and the sensors sync up. If you believe the sensors need to be cleaned you may do so. Do as minimal as possible to make sure you are not damaging the sensor or disrupting the wiring inside. A bad connection would make the lights stay on. With so many lights that are effected by the module being illuminated, the module is likely bad or does not have a connection. Check the connection first and then resort to replacing the unit. For more help with these electrical tests, contact our service department.

ANSWER : The first thing to do is to repair third brake light and replace the brake light fuse and then see if the third brake lights work and the lower lights start working? If only the 3rd brake light starts working then you may need a further checks on the turn signal flasher or switch could be bad.

ANSWER : Hi there. In many cases, when you have electrical problems like you’re describing, it’s caused by multiple electrical component failure. It’s likely that a few electrical relays are not working; especially if you have systems that utilize the same components (such as your brake light and tail lights). I would recommend having a professional mobile mechanic come to your location to complete an electrical problems inspection first, so they can pinpoint what is damaged and recommend the right repairs.

ANSWER : It is possible that you could be having an issue with your powertrain control module. This is somewhat of a common problem on many GM vehicles. I would recommend having your vehicle inspected by the dealership to determine if the powertrain control module is functioning properly. If not, a reflash of the powertrain control module may resolve the issue but often times it must be replaced.

ANSWER : Hello. If the brake pedal is going to the floor then that means that it is not building pressure. If the brake system has been fully bled and there is no air in it then most of the time it is a bad master cylinder or it can be caused by a bad ABS module. If the brake fluid was low and if air got into the system then the only way to properly bleed it is with a scan tool that would allow you to open and close the valves in the ABS unit. Air gets trapped in these easily if the brake fluid gets low. This can also explain why the brakes are locking up. I would usually use my scan tool to bleed the system out first before going any further. I would also scan the brake control module to see what it is reading as a fault. If there is no air in the system and if there is no prominent code then I would replace the master cylinder first. If you want to check out why your brakes are locking up, consider YourMechanic, as a certified mechanic can come to your home or office to diagnose and repair this.

ANSWER : Hi, thanks for writing in. You need to check the brake switch install adjustment. You may have the switch adjusted too tight and it is holding the the brake pedal partly down. This will cause the brake master cylinder to not release the brakes when you let off the pedal. Readjust the switch away from the pedal until you feel some free play again in the pedal. This should fix the problem. If you would like help, consider having an expert automotive technician from YourMechanic come to your home or office to inspect and diagnose this issue for you, and make or suggest any repairs as needed.