07 caliber wont start

ANSWER : Hello. Thank you for writing in. There are several reasons your vehicle may only start when jump starting. The first and most common is a build up of resistance that is causing you to need a boost of voltage to get the engine started. This may be due to poor battery cables, a bad ground connection, a poor starter solenoid, and a couple of other issues. The first thing you want to do is perform a visual inspection of the starting system. Make sure there is no corrosion build up in the battery cables. You can also check the resistance across these wires and make sure you have a solid connection between components. You then want to make sure the starter solenoid is doing its job. It is responsible for taking the small amount of electricity sent by the ignition and turning it into a huge electrical charge that is strong enough to push over the engine with the help of some gear ratios in its favor. Do some more testing, and stick to the basics before assuming its something seriously complicated.

ANSWER : Hi there. There could be two problems here. It is possible that your battery is bad and will not take a charge from your alternator while driving. In that case every time you shut your car off you will not have enough juice to start it again. Inspect your battery – it should have at least 12.5 to 13 volts to start your car, if it doesn’t you will need to replace the battery. The second problem could be that your alternator is bad and not charging your battery, in this case you will need to replace your alternator. Both the battery and the alternator can be tested in your car. If you would like to have the car checked for you, a certified professional from YourMechanic can come to your car’s location to diagnose the starting problem and proceed with repairs.

ANSWER : Hey there thanks for writing in about your 1998 Honda Accord. This could be a few things. A faulty ignition switch, a failing crank sensor, or possibly other faulty sensors could be the cause. To have this taken care of, consider having a certified technician, such as one from YourMechanic, come to your car’s location to diagnose and repair the hard start issue.

ANSWER : Hi There,
The idle air control valve is a small valve on the engine’s intake system that reads the air intake as it comes into the motor. This is controlled by the car’s ECM which uses this information to make adjustments to the air/fuel ratio depending on various inputs such as outside air temperature, intake air temperature, load and various other things. As you accelerate, your car’s engine is receiving a much higher dose of fuel than when at idle and conversely, when you let off the gas pedal, there is a sudden change in this fuel supply as a result of your foot letting off the pedal. When this happens, the job of the idle air control valve is to bring this deceleration down to a slow and smooth idle rather than suddenly cutting off the fuel supply causing the motor to die. When the idle air control valve is not working properly, this cause a disruption in this process resulting in the engine not being able to idle properly. I would recommend having a professional come to your location to diagnose and inspect your vehicle.

ANSWER : Hi and thanks for contacting YourMechanic. Check the battery cables for more corrosion and clean them up again. You may need to put backing soda and water mixture on the terminals to clean the corrosion completely off. Make sure that the cables are tight and also tight on the starter solenoid. By rocking the vehicle back and forth and using the clutch to start the vehicle, this is an indication that the cable on the starter is either corroded or loose. If you need further assistance troubleshooting your starting system, then seek out a technician, such as one from YourMechanic, to diagnose and resolve the issue.

ANSWER : Your vehicle has something called a neutral safety switch that will prevent the vehicle from starting when it is in any gear position other than park or neutral. Occasionally, this switch can malfunction causing the car to stall as soon as you put it into any gear. This switch usually also monitors gear selection data as well to transmit back to the computer. This switch is connected to the starter solenoid which allows it to complete the starter circuit only when the transmission is in park or neutral. I would suggest having a professional from YourMechanic come to your location to diagnose and inspect your vehicle.

ANSWER : It sounds like your starting issues may be linked to a problem with air metering or fuel delivery. A clogged or malfunctioning idle air control valve may show some of the same symptoms you are describing. The idle air control valve can be stuck in a cold start position which may work well if the car has been sitting a few hours, but as the engine warms up there must be a regulation in airflow. Consider hiring an experienced technician like one from YourMechanic who can come out for a closer look at your hard start situation and offer a more personal diagnosis.

ANSWER : Hello, thank you for writing in. With intermittent symptoms, diagnosis can take longer but is typically the same as diagnosing any other starting problem. The main issue is that you can only perform the testing needed when the issue is occurring. If the vehicle starts and works normally, all of the components are likely going to pass their tests. There are several components that will work intermittently. They include the fuel pump, charging system, a number of sensors, and any electrical connection that is loose. When the vehicle is not starting, test for fuel pressure, spark, and the electrical connection on any of the sensors that effects starting (air intake, camshaft/crankshaft position sensors). For more diagnostic help, contact our service department to schedule an appointment.