What does the AdvanceTrac® Light mean on the dash?

What does the AdvanceTrac® Light mean on the dash?
Experienced mechanics share their insights in answering this question :
Your car is equipped with an advanced traction and stability control system called AdvanceTrac®. The system is always on unless you manually turn it off. The AdvanceTrac® Light should come on in the dash when you first crank the engine and then go off. If it comes on while you’re driving, it means that the system has been activated automatically and that slippery conditions have been detected. This is normal. However, if the light stays on, it means you need to have your traction control system inspected immediately.

Tip

If the light stays on, it means the traction control system is disabled. You can drive normally, but have the car inspected.

How to Identify and Fix Common car Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced mechanics :

Low tire pressure. Faulty steering wheel angle sensor. Faulty wheel speed sensor. Low brake fluid.
The AdvanceTrac warning light means that service is needed on your vehicle`s AdvanceTrac system.
If the issue is related to a wheel speed sensor or and ABS issue, it is ok to drive the vehicle and the warning light should have no affect on your driving. The AdvanceTrac system is only an extra feature to help the vehicle maintain traction and is not required for normal driving.
The Ford AdvanceTrac is a technology that was built to navigate through the harshest road conditions. It is an electronic stability system that helps the driver navigate through tough terrains like ice, snow, gravel, and dry pavement. The AdvanceTrac is designed to enhance stability and traction in your Ford vehicle.
Barring that, you should be able to reset the AdvanceTrac light by disconnecting the ground terminal of the battery. After the battery is disconnected, hold the brake pedal for a few seconds to make sure any power left in the system is discharged. Next, reconnect the battery.
In some cases, the warning light may come on because wheel-speed sensors are covered with road grime or debris. When the traction control warning light stays on, that means you aren`t getting any help from the system to control traction and the system needs to be checked.
When the traction control light comes on while driving, take caution. This safety feature typically means that the car`s traction control is being used, indicating that your vehicle briefly lost grip going around a sharp curve, driving on wet pavement, or the like.
Travel safely in your Ford Car, SUV, Crossover or Pickup that is equipped with the Advanced Traction Control System (AdvanceTrac™), a technology that distributes power between the wheels to avoid skidding with the risk of tipping over and thus maintain total control of the Vehicle, delivering a driving experience full …
Why your Ford Escape traction control light turns on. in your Ford Escape is meant to warn drivers of a loss of traction—so if you see this light come on while you`re driving, it probably means your traction control system is working exactly how it`s meant to.
Traction Control Is Turned Off

So, if your vehicle`s traction control light is on, it may be as simple as making sure your traction control is not turned off. Commonly located near the steering wheel on the instrument plane, you will be able to turn it back on via a simple switch.

If the traction control module is going bad or failing, it may be more difficult to maintain control of the vehicle when braking during adverse weather conditions, such as ice or rain. The traction control system (TCS) and the anti-lock brake system (ABS) work together to maintain control when hydroplaning.
This is usually caused by a failing throttle body. The throttle motor or sensor fails and will cause this to occur.
The magnetic operation on the traction control sensors or Anti-lock Braking sensors can be interrupted by dirt or other buildups. Another common sensor problem is with the electrical connections between the sensors and the vehicle`s computer.
Traction Control and Intelligent four-wheel-drive, which keeps track of the car`s stability on difficult terrains and adjusts the powertrains and braking systems to avoid slippage.
When turned off, you may notice that your vehicle handles differently than you are used to when driving on slippery surfaces. This is why you should leave your traction control on at all times.
In some cases, the warning light may come on because wheel-speed sensors are covered with road grime or debris. When the traction control warning light stays on, that means you aren`t getting any help from the system to control traction and the system needs to be checked.
In some cases, the warning light may come on because wheel-speed sensors are covered with road grime or debris. When the traction control warning light stays on, that means you aren`t getting any help from the system to control traction and the system needs to be checked.
The traction-control light is usually a sign that your vehicle is working properly by maintaining traction on a slippery road, but it can also mean that your car has some damaged sensors or wires. Keep yourself safe on the road by taking your vehicle to a trusted auto repair shop at the first sign of trouble.
The AdvanceTrac® Light should come on in the dash when you first crank the engine and then go off. If it comes on while you`re driving, it means that the system has been activated automatically and that slippery conditions have been detected. This is normal.
When the traction control light comes on while driving, take caution. This safety feature typically means that the car`s traction control is being used, indicating that your vehicle briefly lost grip going around a sharp curve, driving on wet pavement, or the like.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

No dash lights, back right tail light is out, no parking lights. Brake lights work though as does head lights.
ANSWER : Hi there. In many cases, when you have electrical problems like you’re describing, it’s caused by multiple electrical component failure. It’s likely that a few electrical relays are not working; especially if you have systems that utilize the same components (such as your brake light and tail lights). I would recommend having a professional mobile mechanic come to your location to complete an electrical problems inspection first, so they can pinpoint what is damaged and recommend the right repairs.

Abs light, emergency brake light, steering wheel assist light, engine light, EPC light, traction control light
ANSWER : Hello, thank you for writing in. The vehicle does utilize a lot of the same sensors for these systems. Are there any other codes that are coming up when this code appears? If so you will want to take these into consideration when processing the repair and making a diagnosis. The module may be bad, and replacing it should fix the problem. The lights should turn off once the main computer recognizes the new module and the sensors sync up. If you believe the sensors need to be cleaned you may do so. Do as minimal as possible to make sure you are not damaging the sensor or disrupting the wiring inside. A bad connection would make the lights stay on. With so many lights that are effected by the module being illuminated, the module is likely bad or does not have a connection. Check the connection first and then resort to replacing the unit. For more help with these electrical tests, contact our service department.

First, the fuse 19 keeps blowing. When I hit the brake pedal my dash lights up. The third brake light acts like a running light.
ANSWER : Hi there. Check the wiring on the vehicle to the tail and brake lights. There is a cross short that is causing the lights to blow the fuses and make the tail lights brighter than normal. If you need further assistance with your electrical issues, then seek out a professional, such as one from Your Mechanic, to help you.

signals, daytime running lights are not working, park brake light on dash is on steady and chime is dinging steady 4×4 wont engage
ANSWER : This is likely a brake light switch problem. I would suggest testing the brake light switch which should be located down by the brake pedal. This may also be a computer problem as well as indicated by the other lights on in the dash. I would recommend having an expert from YourMechanic come to your home to possibly replace the brake light switch and diagnose with a scanning tool which will download useful data from the truck’s computer indicating what specifically the problem may be.

Dash, Tail/brake, dome, trunk, glovebox, and door lights won’t work, dash doing weird things.
ANSWER : Hi there. Sure would appear a lot is going on electrically all at once. This could be, a problem in the PDC (power distribution center). The PDC is typically located under the hood and contains numerous fuses and relays. I don’t believe any one fuse will resolve all of the electrical issues. There is a possibility, it is not a power supply issue. It may be, the result of a poor electrical ground common to the inoperative components. Proper circuit testing should be performed. This would confirm the cause of multiple electrical failures. I recommend having your vehicle’s electrical problems be diagnosed and repaired by a certified technician, such as one from YourMechanic.

My dash lights don’t come on but all other lights knobs etc do
ANSWER : Hello there, a few different faults could cause your 2004 Chevrolet Silverado to have dash lights that do not illuminate. Given than the fault is interment it sounds like an electrical issue. The most common would be a failed dash light bulb, a wiring harness fault, or blown fuse. A qualified technician such as one from YourMechanic will be able to diagnose your dash lights by performing a vehicle inspection and make any repairs required.

ABS light on, ESP light on,Traction OFF light on, engine light on, rides perfectly OBDI reads only Front Right Wheel Speed Sensor
ANSWER : If a faulty component is still in place, the fault codes will return almost immediately after clearing them. ABS, ESP, and traction control systems all rely on input from wheel speed sensors to determine as the name implies, the speed of each wheel. When a wheel, or wheels are spinning faster than others due to wheel slip or the vehicle is sliding, the ABS and ESP systems can reduce throttle input as well as apply braking to an individual wheel or all of them if needed. With a wheel speed sensor fault code stored, these systems cannot determine the rate that all 4 wheels are spinning and sets a fault. That is why the abs/esp light is on. The system should be scanned by a certified technician and the wheel speed sensor replaced if found to be the cause. The warning lights will stay on and these systems will not function as designed until the fault is corrected. These lights do not come on to indicate a need for routine service. Rather they only come on when a component in the system is at fault.

2012 equinox reduced power light engine light and traction light came on. Lost a lot of power got home and all light except engine
ANSWER : Your car has what is called a "safe mode" that will be engaged by the computer when it detects that something critical has gone wrong related to any of the major components in your engine chassis or power train. This may be related to a number of things, most of which should have been registered in the computer when the check engine light came on. I recommend having an expert from YourMechanic come to your location to inspect your check engine light and diagnose any codes registered by your vehicle’s computer.