Valve cover gasket and starter labor and parts? mechanic charging me 900.00

need a round about price on a val cover gasket and starter for a 2004 Nissan xterra / / mechanic trying to charge me 900.00 for both.

when they repair the gasket do they repair both sides?

My car has 154182 miles.
My car has an automatic transmission.

Experienced mechanics share their insights in answering this question :
Yes, on the valve cover gasket repair, they replace both sides.

How to Identify and Fix Common car Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced mechanics :

A valve cover gasket is an engine component designed to protect cylinder head hardware from the elements and prevent oil from escaping the engine. Typically, the gasket is made of plastic, rubber or cork to create a tight seal between the engine cover and engine, acting as a two-way barrier.
The most common reasons a Nissan Xterra won`t start are a dead battery, an alternator problem, or failed starter.
A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.
Silicon rubber: Silicon rubber valve cover gaskets are easy to replace, and tend to hold up better where breakage is concerned.
Your car may have 1 or 2 valve covers depending on its configuration. A straight 4 or 6 cylinder engine will have 1 valve cover, while “V” configured engines like a V6 or V8 will have 2 valve covers, one on each side.
For this application, Permatex No. 1, RTVs or Permatex High Tack gasket sealant work well. Tip: after gluing the gasket to the cover, place the gasket on a flat surface and place a weight on top of the cover until the sealant dries.
The book time calls for approximately 3.5 hours to complete the replacement of both valve cover gaskets. But this will vary by mechanic, but this is the average book time.
Recommended Services. The engine valve cover gasket should last for about 8 to 12 years. If the gasket is leaking, then the PCV (Positive Crankcase Ventilation) valve is plugged up causing the engine to build up too much crankcase pressure blowing out the gasket.
The Nissan Xterra is a truck-based compact SUV manufactured and marketed by Nissan from 1999–2015 across two generations; the first (1999–2004) sharing a platform as well as front bumper, hood, A-pillar, windshield and front doors with the Nissan Frontier pickup – and the second (2005–2015) also sharing its platform …
Defective fuel pump or filter: Since the fuel pump is responsible for supplying your vehicle with fuel, it can cause a loss of power when it begins to wear out or when the in-tank filter becomes clogged and prevents the free flow of fuel.
One of the most common causes for a Nissan not starting is due to an issue with the battery. The first thing to do is make sure all of the connections are on tight, as this can sometimes cause problems with starting.
So can a bad starter drain your battery? The short answer is: Yes, it can. It could also drain the battery even faster if you repeatedly try to start your car with a faulty starter. A faulty starter is also one of the leading causes of battery overcharging.
Where Is the Starter Located in a Car? The starter is found on the driver`s side of the engine. It`s typically placed just beneath the left bank of cylinders.
Push-start the vehicle if you have a manual transmission.

Once you`ve got some speed going, release the clutch and your car should start. Press the clutch back in and give your engine some gas and you`re good to go! This will definitely work with a bad starter, but it could also work with a bad battery.

Your starter can usually be found on the passenger`s side (if RWD) of the engine, just below the exhaust manifold. Or if it is FWD, check on the drivers side above the transmission or under the exhaust manifold. They can also be located just under the intake manifold on some vehicles.
Push-start the vehicle if you have a manual transmission.

Once you`ve got some speed going, release the clutch and your car should start. Press the clutch back in and give your engine some gas and you`re good to go! This will definitely work with a bad starter, but it could also work with a bad battery.

Your starter can usually be found on the passenger`s side (if RWD) of the engine, just below the exhaust manifold. Or if it is FWD, check on the drivers side above the transmission or under the exhaust manifold. They can also be located just under the intake manifold on some vehicles.
Push-start the vehicle if you have a manual transmission.

Once you`ve got some speed going, release the clutch and your car should start. Press the clutch back in and give your engine some gas and you`re good to go! This will definitely work with a bad starter, but it could also work with a bad battery.

Your starter can usually be found on the passenger`s side (if RWD) of the engine, just below the exhaust manifold. Or if it is FWD, check on the drivers side above the transmission or under the exhaust manifold. They can also be located just under the intake manifold on some vehicles.
Where Is the Starter Located in a Car? The starter is found on the driver`s side of the engine. It`s typically placed just beneath the left bank of cylinders.
Your starter can usually be found on the passenger`s side (if RWD) of the engine, just below the exhaust manifold. Or if it is FWD, check on the drivers side above the transmission or under the exhaust manifold. They can also be located just under the intake manifold on some vehicles.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Valve cover gasket and starter labor and parts? mechanic charging me 900.00 – 2004 Nissan Xterra
ANSWER : Yes, on the valve cover gasket repair, they replace both sides.

How much does it cost for Camshaft cover and Valve cover gaskets, parts and labor?
ANSWER : Billing question sent to CS for the cost of replacing the valve cover and camshaft cover gaskets with the cost of labor on a 2008 Mercedes-Benz CLK350 with a V6-3.5L engine.

Pete, I need valve cover gaskets and timing cover gaskets replaced, I have the gaskets / kits for all. Price please? Thanks, David
ANSWER : Hi there. Typically when the timing cover gasket is replaced, the cover itself should be replaced as well. To receive an estimate for this service, and the valve cover gasket, please click this link and enter your vehicle information and services requested. Once we receive the data, we’ll send you a quote via email. Thanks.

I was told to change my valve gasket and valve cover. Should I?
ANSWER : Hi, thanks for writing in. Five years is a bit on the early side to have a leaking valve cover gasket. The labor time is 3 hours to replace that gasket and YourMechanic typically charges around $400 (part and labor) but there is some variance from region to region. The second estimate that you received is clearly high but not sure if that second estimate includes a new valve cover. The original cover is normally re-usable and if anyone proposes to replace it, they should show you clear evidence of a major problem. It is best not to have engine oil leaks, but if the leak from the valve cover is small, not dripping on a hot manifold (fire hazard) or dripping onto rubber motor mounts, wiring, and so forth you can wait a little while to repair it. Here at YourMechanic, we can have a technician come to your home or office to perform your valve cover gasket replacement for you.

I have a 2001 Toyota Tundra 4.7 V-8. When replacing the valve cover gasket, what should I torque the valve cover back to when rein
ANSWER : The valve cover bolt is tightened to 60 inch pounds.

Turbo VS. Non-Turbo Valve Cover Gasket
ANSWER : Hi there. Looks like the gaskets are the same for the turbo and non turbo engines. I recommend asking the local parts store for to see a valve cover gasket for the non turbo engine and a gasket for a turbo engine and compare the two gaskets. If the gaskets are the same material and have the same design, the go for the valve cover gasket that will fit your budget. If you need further assistance with the valve cover gasket, then seek out a professional, such as one from Your Mechanic, to help you.

After valve cover gasket replacement, compressor broke
ANSWER : Hi there. Thanks for writing in about your 2000 Lexus GS400. Compressors can go bad due to oil saturation. It is likely that the technician spilled additional oil on the compressor when replacing the valve cover. The technician may have dealt the final blow to the already weakened compressor if they did spill such additional oil onto it. Unfortunately there is no real way to prove if this was done or not. If you need to have this taken care of, a qualified professional, such as one from YourMechanic can take a look at the car and replace the compressor if necessary.

2012 chevy cruze lt 1.4 valve cover vacuum leak. waiting on parts in the mail.
ANSWER : It is possible to temporarily seal air (vacuum leaks). Any method that best creates a seal can be used. In particular, RTV sealant which is flowable can be used to seal a non moving crack so long as the surface that you are applying the RTV to is oil and dirt free (otherwise the RTV wont bond). The only concern with such temporary (or even permanent) repairs is that you do not get any foreign matter in the engine through any crack that you are trying to seal. If you want the PCV valve and/or the valve cover replaced you can request PCV/valve cover replacement service and the responding certified mechanic will get this taken care of. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.