truck won’t start
truck ran fine and then sat for 4 years. put in a new fuel filter and that didn't work what else can I do to get this truck started
My car has 97000 miles.
My car has an automatic transmission.
Experienced mechanics share their insights in answering this question :
The fuel in the fuel tank could be bad and would need to be removed and the tank flushed with clean fuel. The fuel pump may not work and would need to be tested for proper pressures.
Depending on the type of fuel injection system the engine has, it may need to be cleaned out or in some cases, the injectors will need to be replaced if clogged.
I recommend replacing the fuel first and putting some injector cleaner in the fuel. Then test the fuel pressure and whether fresh fuel is getting to the injectors. It should start.
How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
Leaking Fuel Injectors that do not seal completely when turned “off” can cause the following problems: Hard Starting – Hard starting Hot or cold due to fuel leak down with loss of fuel pressure, and little or no initial starting fuel pressure. Idling Problems. Increased Fuel Consumption – Poor fuel economy.
A faulty regulator can prevent the engine from getting proper fuel pressure, resulting in a vehicle that cranks but doesn`t start.
One of the most common reasons for fuel injector`s failure is carbon buildup due to low-quality fuel. Carbon buildup can make it difficult for the injectors to spray fuel into the cylinders and that results in loss of performance. You can solve this issue by using a high-quality fuel system cleaner.
If the car cranks when you turn the key, but the engine won`t start, it could be because fuel isn`t getting to the engine. One potential reason for this could be dirty fuel injectors. Over time, the fuel injector nozzles can become clogged with rust, corrosion or debris.
These include a bad fuel pump relay or control module, a blown fuse, a wiring fault, loose or corroded wiring connector at the pump, or even an issue with the anti-theft system. Until these other possibilities have been checked out and eliminated, the fuel pump should be the last thing that`s replaced.
If there is still no pressure, then replace the fuel filter and retest. If nothing after that, then the fuel pressure regulator is not working and needs replacing. If you get pressure to the rail, then there could be a problem with the injectors; they may be either dirty or plugged up.
Your engine won`t start. While the cause could be a range of issues related to fuel, compression, or spark, the fuel pump is often a likely culprit.
The throttle position sensor (TPS) is usually connected to the throttle plate shaft in the throttle body. The TPS reads the angle of the throttle valve and transmits an electrical signal to the PCM. The PCM uses this real-time signal to help calculate or modify fuel injector pulse width, controlling air/fuel mixture.
Electronic Control Unit (ECU)
It does this by telling the fuel injectors when and how long to fire. The ECU often controls other functions like the fuel pump and ignition timing.
The most common reasons a Chevrolet Silverado 1500 won`t start are a dead battery, an alternator problem, or failed starter.
If the engine cranks, but the car doesn`t start: Bad fuel pump: A faulty fuel pump won`t deliver fuel to the engine, even if you`ve just filled up. Bad spark plugs: Without hot sparks to ignite the fuel charge in each cylinder, there is no combustion and no expansion of the burning mixture.
If your vehicle won`t start, it`s usually caused by a dying or dead battery, loose or corroded connection cables, a bad alternator or an issue with the starter. It can be hard to determine if you`re dealing with a battery or an alternator problem.
Decreased Fuel Pressure
Low fuel pressure can lead to engine misfires, low acceleration, rough idles, and engine stalls. If your check engine light is on and your car has been stalling out, you may have a fuel pump failure.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Fuel pump engages. Batery good, alternator good volts, jump start helps when wont start. Temp does not matter. Intermittent?
Hello. Thank you for writing in. There are several reasons your vehicle may only start when jump starting. The first and most common is a build up of resistance that is causing you to need a boost of voltage to get the engine started. This may be due to poor battery cables, a bad ground connection, a poor starter solenoid, and a couple of other issues. The first thing you want to do is perform a visual inspection of the starting system. Make sure there is no corrosion build up in the battery cables. You can also check the resistance across these wires and make sure you have a solid connection between components. You then want to make sure the starter solenoid is doing its job. It is responsible for taking the small amount of electricity sent by the ignition and turning it into a huge electrical charge that is strong enough to push over the engine with the help of some gear ratios in its favor. Do some more testing, and stick to the basics before assuming its something seriously complicated.
Vehicle won’t start, once it’s jump started it only stays running until you turn it off, then it work start again without jumping.
Hi there. There could be two problems here. It is possible that your battery is bad and will not take a charge from your alternator while driving. In that case every time you shut your car off you will not have enough juice to start it again. Inspect your battery – it should have at least 12.5 to 13 volts to start your car, if it doesn’t you will need to replace the battery. The second problem could be that your alternator is bad and not charging your battery, in this case you will need to replace your alternator. Both the battery and the alternator can be tested in your car. If you would like to have the car checked for you, a certified professional from YourMechanic can come to your car’s location to diagnose the starting problem and proceed with repairs.
Truck won’t start in morning. 2nd day now. Battery seems good.
Since the symptoms changed when you touched the battery terminal, it leads me to believe you may have a poor connection and the main battery terminals. If they are badly corroded or have any small cracks, the terminal may be too loose on the battery. You can rule out the battery by removing the connection to the vehicle then testing the battery itself. If the battery is good then reattach the terminals, tighten them and see if you are able to wiggle them on the posts. If the terminal still moves, replace the entire cable. You can cut the terminal ends and replace them, but you will never get as perfect a connection as replacing the whole cable. Consider hiring an experienced technician like one from YourMechanic who can come out and take a closer look at the loss of electrical power situation and run tests to offer a more personal diagnosis.
Truck won’t start
Hi, thanks for writing in. I’d be happy to provide my insight. There are a variety of potential issues that may have caused this. The oil light coming on should not have anything to do with the truck stalling unless the oil level is severely low and the truck’s computer may have gone into "safe mode", which is a safety feature of the truck that is engaged when something goes wrong with the truck that may be catastrophic in terms of engine failure or safety. When this happens, the computer simply shuts the truck down and will not allow it to move in an effort to preserve the engine and safety of the passengers.
If you would like help, consider having an expert automotive technician from YourMechanic come to your home or office to inspect and diagnose this no-start issue for you, and make or suggest any repairs as needed.
My car won’t start, neither does my auto. Start. Sometime it might start if I jump it sometimes it won’t.
Hi there. There are a number of issues that will make a car hard to start. Everything from the electrical system to the fuel system to the actual starter itself can be the problem. Finding the root cause of a hard starting engine can take some investigation. Ignoring a hard starting issue can further damage the vehicle, which will often result in a more expensive repair. You might want to have a mobile mechanic complete a car is hard to start inspection so they can pinpoint the source of the issues you’re having and recommend the right repairs be completed.
The car crank but won’t start
Hi there. This does sound like an issue with the wiring. If the check engine light is coming on every now and then this means that when it does not come on there is no power to the computer. This can be the wiring harness issue or an ignition switch problem. I would have to test for voltage to the computer when the problem is occurring to be able to find where the issue lies. If you need assistance, a certified YourMechanic technician can be dispatched to your location to inspect your vehicle’s non-start issue and suggest any necessary repairs.
I changed the fuel pump and truck ran great for 3 days. Now after 3 days, the truck dies. It will start running for a few minutes, then dies like before.
Hi there, thanks for writing in. I’d be happy to help. It sounds like you should disconnect the connector to the fuel pump and inspect it for any signs of getting hot. The female connections may be too loose on the fuel pump and lose contact after running and getting hot. If there are indeed any signs of problems, then I’d suggest replacing connector and adding dielectric lube to pins before installation. This should solve the problem, but if you continue to experience issues, feel free to reach out to us for help again.
I parked my truck for 5-10 mins. Tried to turn it on, now it wont start, called a tow tow truck 15-20mins later my truck turned on
It is very likely that you have a powertrain control module failure. This can happen often on many GM vehicles. I would recommend having the powertrain control module tested and replaced as necessary in order to resolve this issue. After the powertrain control module is replaced, a reflash procedure will be required so that the vehicle can relearn all of its primary engine data. Once the reflash is completed, your vehicle should no longer have this issue.