How to Identify and Fix Common car Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced mechanics :
This indicator light stays on for a few seconds when the ignition is switched ON. If the TCS or DSC is operating, the indicator light flashes. If the light stays on, the TCS, DSC or the brake assist system may have a malfunction and they may not operate correctly.
Because the ABS and traction control often share the same module, a problem with one mechanism might be indicated by a light for both. If the brake system is malfunctioning, the traction control light might come on as a result. The light for your ABS might also come on if the brake fluid is low.
The light flashes if the Electric Parking Brake (EPB) has a malfunction. If the light remains flashing even if the Electric Parking Brake (EPB) switch is operated, consult an Authorized Mazda Dealer as soon as possible.
Contact an expert repairer, we recommend an Authorised Mazda Repairer to have your vehicle inspected. If the ABS warning light stays on while you`re driving, the ABS control unit has detected a system malfunction. If this occurs, your brakes will function normally as if the vehicle had no ABS.
The most common cause of the DSC fault light showing up is a low vehicle battery or a bad connection at the battery. This system requires a certain amount of voltage, and if it does not receive it then this will occur.
If the TCS and the ABS warning lights both come on, along with the red main brake warning light, you should not drive the car until the problem has been fixed. Your entire braking system is affected, and may not be able to stop your vehicle when you need it to. Have your vehicle towed to a repair shop.
Step One: Disconnect the positive cable from your car battery. Then, hold down the brake pedal to drain the vehicle`s electrical system. This will result in a reset of the car`s central computer. Plug the cable back in to restore power.
Why is the brake light on while driving? When your brake light comes on, your car is letting you know that either your vehicle is low on brake fluid, the emergency brake is activated, there`s trouble within the ABS unit, or there`s a problem with the sensors.
While you`re driving, a dashboard warning light may illuminate or flash in an alarming red colour (depending on the vehicle model), to indicate a problem with the braking system. Drivers sometimes ask whether it`s safe to drive with this brake light on. The answer is no; it should never be ignored.
The ABS brake light doesn`t mean you have zero braking capability. Instead it means that your brakes are now on their own, and you are too. If conditions are bad, your brakes will perform like brakes did before ABS. Without regulation, your brakes may stick right when you need them the most.
When your car`s ABS light comes on, it means there is a problem with your vehicle`s braking system. You need to address this issue; otherwise, it could make your car unsafe to drive. ABS is a type of braking system used in all cars produced since Sept.
If your ABS light comes on individually, you are safe to drive your car to your destination, as your normal brakes will still work. You will, of course, have to be more careful as your ABS will not respond in case of an emergency.
DSC/TCS（Dynamic Stability Control system and Traction Control System） The Dynamic Stability Control system (DSC) automatically takes control of the vehicle when skidding is detected.
Use the keypad to enter the code “*72.” This resets the smoke sensors, which will cause the alarm to stop if it is still ringing. If your keypad has an “Enter” button, press this once you have entered the code.
When the system is damaged or needs a part to replace, it can cost anywhere from $320 to $1,000. The exact cost really depends on your car and the components of its given ABS system.
Sometimes a blown fuse to the ABS can cause the light to come on and stay on. Fuses are easy to blow, so sometimes it`s an easy fix to check.
Wheel speed sensors are often called ABS sensors. You`ll find them mounted on the axles of all ABS equipped vehicles. Look for this sensor on your wheel hubs, near the brake rotors. You`ll find the rear wheel speed sensor mounted on the rear axle housing or wheel cylinder.
What Is an ABS Code? An ABS code detects problems associated with your braking system. These warning lights flash on your dashboard when mechanical issues arise due to abnormal signs from the wheel sensors.
The primary input of the TCS is the wheel speed sensor. These sensors continuously monitor the speed of each driven wheel and send the data to the ABS and Traction Control System ECU. When a slip is detected between the tire and the road, the TCS regulates brake pressure on the slipping wheel.
The ABS (anti-lock braking) and ESP (electronic stability program) lights usually come on at the same time because the two systems share components. WHen the lights are on, it means that the controller has seen a malfunction and stored a fault code describing that malfunction.
In order to operate, your ABS system needs electricity. This is controlled by the anti-lock fuses and relay. The first fuse (a 10 amp fuse) must be good in order for electricity to flow to the relay, and the relay must function to provide power to the second fuse (a 30 amp fuse).
If the ABS system is not functioning properly, then your vehicle is likely to skid, hydroplane and lose traction under heavy braking conditions. The last time you want to find this out is when you need it most in tough conditions, which could lead to an accident on the road.
Insert the key (or key fob) in the ignition. Move the key to position 2, but don`t start the ignition. Open the driver`s door and wait for approximately 10 seconds. After completing the above three steps, the brake pad lights should reset!
Amber Brake Warning Light
The yellow (ABS) warning lamp indicates an electrical problem in the ABS, like the controller or a sensor. A faulty wheel speed sensor will illuminate the yellow (ABS) warning lamp.