Pls I need location for 2013 Hyundai Velecle speed

Pls I need location for 2013 Hyundai

My car has an automatic transmission.

Experienced mechanics share their insights in answering this question :
If you are referring to the vehicle speed sensor, the vehicle speed sensor is typically located externally on the transmission. There will likely be one or two small bolts that hold it to the transmission. There will also be an electrical connector hooked up to it. If you are in doubt about this repair, consider YourMechanic as a certified professional can come to your home or office to replace your vehicle speed sensor for you.

How to Identify and Fix Common car Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced mechanics :

Equipped with this engine, the 2022 Hyundai Sonata takes 7.85 seconds to reach 60 mph from a standstill and achieves the quarter-mile in – seconds. The 2022 Hyundai Sonata can reach a top speed of 128 mph with this engine configuration.
The mileage of Sonata Petrol ranges between 12.2 kmpl – 13.08 kmpl.
It is usually located in the engine compartment, but there are cases where it can be present on the passenger`s side, under the dashboard or the glove compartment.
The speed rating is displayed on the tyre`s sidewall, after the load rating. In this example, the car`s speed rating is W, which indicates that it has been legally approved for use up to 168 mph.
Optimal Tire Pressure

On all four Hyundai Sonata wheels there should be a cold tire pressure level of 34 psi.

Hyundai Ioniq 5 top speed is 185 Kmph. Check similar car details: What is the top speed of Kia EV6? What is the top speed of Volvo XC40 Recharge?
The Hyundai Sonata 1.6 T Limited 182 PS claimed top speed is 220 km/h / 137 mph.
The 2013 Hyundai Sonata is a good used car. It`s among the most fuel-efficient midsize sedans, and its interior is quite comfortable. Above-average reliability, below-average ownership costs, and strong safety scores enhance its desirability.
All Sonata versions use four-cylinder engines, a naturally aspirated 2.4l or a turbocharged 2.0l.
This is why when it comes to locating your ECM it`s best to consult your vehicle`s owner`s manual to find the exact location, but typically they are found in the engine compartment, under the passenger floorboard, under the seats, or behind the kick panels.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Pls I need location for 2013 Hyundai Velecle speed
ANSWER : If you are referring to the vehicle speed sensor, the vehicle speed sensor is typically located externally on the transmission. There will likely be one or two small bolts that hold it to the transmission. There will also be an electrical connector hooked up to it. If you are in doubt about this repair, consider YourMechanic as a certified professional can come to your home or office to replace your vehicle speed sensor for you.

when driving speed slow down and resume to speed it begins to jerk i have to put in over drive to resume speed especially on hiway
ANSWER : You should have the vehicle scanned. The data from the speed sensor needs to be checked to see if the transmission or engine is the cause of the jerking. You may have a transmission solenoid that’s not shifting correctly, an engine misfire, or a sensor malfunction. Have a certified mechanic, like one from YourMechanic, scan and test your vehicle for you to properly diagnose the car’s jerking symptom.

Engine swap details needed. I need to know if the swap will fit.
ANSWER : Hi there. When it comes to swapping engines for your vehicle, what you can do is check all of the engine mounts and transmission mounts and make sure that they will work. If the mounts are a little off but there is room, then you may have to retro fit a custom mount. Check the length of the engine and the transmission assembly together. Make sure that the assembly is the same length. It may be okay if it’s a few inches shorter or longer, however, it cannot exceed 3 inches or the assembly will not fit. There has to be room for the engine to move around. Also, keep in mind, the CV shafts may not match up to the transmission and wheel hubs, especially if the transmission is shorter or longer. If you need further assistance with swapping your engine with another engine, then seek out a professional, such as one from Your Mechanic, to help you.

Problem with speed. No check engine light on but when accelerating speed, it decreases then speeds right back up. No stalling at all
ANSWER : Hi, thanks for writing in. This is a common problem associated with fuel/air delivery which is very commonly related to what is called a mass airflow sensor. This monitors the flow of air intake into the throttle body as it is mixed with fuel to deliver the right air/fuel mixture into the motor. When this is not working properly, this will cause this kind of hesitation or surging when trying to accelerate. I would recommend having an expert from YourMechanic come to your home or office to confirm a diagnosis on the issue and make or suggest the necessary repairs or replacements.

Broken headlight, need a new front bumper, and plastic covering at the bottom of car needs fix? How much is the overall cost? 2013 Toyota Camry
ANSWER : Hello – this task is best handled by a collision repair estimator at a reputable paint and body shop. S/he is trained to evaluate visible and not-so-visible damage, and the costs to repair. Contact a reputable paint and body shop in your area for an estimate and repair.

Hi, do you have 24 hours service? I need to fix my left signal light front because I need the car by 10 a.m. tomorrow, only 1 light.
ANSWER : Billing question sent to CS for the cost of replacing the left turn signal light on a 2010 Hyundai Tucson with a L4-2.4L engine.

car is barely picking up speed from stationary position to 3rd gear
ANSWER : Hi there. Check the turbo on the engine. With the loss of power until the vehicle is driven normally after 100 meters and the lack of power going up steep hills, the turbo could have failed causing the engine to lose power. Remove the intake hose to the turbo and start the engine. Look to see if the turbo is spooling up or not. If its not spooling up, then the turbo shaft could be seized and would need replaced other wise the waste gate could be not functioning causing the turbo to stop boosting. I recommend seeking out a professional, such as one from Your Mechanic, to help you diagnose your loss of power.

I have a 2004 Dodge Dakota that needs the front wheel hubs changed. It is 4wd with all wheel ABS. I need some tips.
ANSWER : When I replace a hub, I don’t necessarily remove the CV joints. I do, however, remove the nut that is holding the CV joint onto the hub. You will need to remove the brakes and rotor, the upper and lower ball joints (replace if damaged), remove the tie rod end (replace if damaged), and the sway arm from the hub.

This should be all you need to remove to take off your hub. Remember, if you damage any boots you will need to replace the part for your safety. Before doing all of this, you may want to get an assortment of cotter pins as well. If you want some assistance, be sure to have a professional mechanic, such as one from YourMechanic, perform a wheel hub replacement.