Driveshafts going bad

ANSWER : Hi there. From the description you provided, your vehicle has problems with the transmission again. You stated it will not shift into 3rd gear again, like before the transmission was rebuilt. If the transmission is again the problem, it should be covered under warranty. It could be a faulty shift solenoid. The shift indicator not reading properly could be a faulty transmission position sensor. If this is an overall lack of performance issue, according to your last statement, then possibly you have a restriction in the exhaust system. I recommend having your vehicle’s problems inspected and diagnosed by a certified technician from YourMechanic.

ANSWER : Hi there. When a car is slow to accelerate it can be caused by multiple issues, ranging from fuel systems that are clogged or damaged to an ignition system component failure. It is also possible that something in the driveline system is dragging which causes the lack of acceleration. Since there are so many different possible issues, the best way to start the diagnosis process is to have a professional mobile mechanic from our team come to your location and complete a car is slow to accelerate inspection.

ANSWER : It is possible that your clutch has failed. The sound you are hearing is likely due to the clutch not engaging with the engine due to it being worn. I would recommened having your transmission inspected by a qualified transmission expert to determine if your clutch requires replacement in order to resolve this issue. This inspection may require removal and partial disassembly of the transmission in order to verify that the clutch has failed.

ANSWER : Pulleys do go bad because the grease in the pulley bearing dries out, the ball bearings and bearing races get pitted and then the pulley becomes noisy. Sometimes, the pulley will actually seize. However, it will be EASILY evident if a pulley bearing is bad. So, all you need to do is have them PROVE the failure to you. If the pulley turns SMOOTHLY with no resistance and there is no noise, then there is nothing wrong with the pulley. Tensioners combine a pulley with a "tensioning" mechanism. If the pulley on the tensioner is good, to check the tensioning mechanism, just ask the shop personnel how many pounds they are able to measure (using a Gates gauge) as "belt tension" with the tensioner installed. If they can measure an installed belt tension of at least 80 to 110 pounds on the serpentine belt, you are fine. As far as alternator failures, even if all pulleys seized, the serpentine belt snapped and all the accessory drives came to a crashing halt, such would have no effect whatsoever on the mechanical or electrical function of an alternator. Alternators are DRIVEN by the serpentine belt. All that happens when the belt disappears or pulleys seize is the alternator stops turning; there is NO possibility of damage to the alternator. Once you re-apply a new belt, or new pulleys, the accessories start turning again, just like before and the alternator produces current to charge the batteries. As noted, pulleys do wear out…worn pulleys do cause noise but all that is beside the point. Insofar as your concern, you CAN confirm if they are telling the truth by just simply having them PROVE the alleged failure to you. If they cannot prove it, or are unwilling to prove it (don’t buy the "insurance rules don’t allow you in the shop trick), then do not replace the pulleys. In the future, you can save a lot of money by having a repair like this, as well as maintenance, performed on a mobile basis. So, please keep us in mind and if additional concerns arise related to your current issue, please don’t hesitate to inquire further.

ANSWER : When you say you have three bad sensors I can only assume you have had them tested and the end result is three bad sensors. If they tested bad then they should be replaced. The power steering sensor senses the load of the steering on the engine so it can raise the idle during parking maneuvers. The O2 sensor is used for fuel control and it may effect engine power and fuel mileage. The camshaft sensor cay cause no starts, engine running problems and all three will turn on the check engine light.

ANSWER : Hi there. The issue could be with the output shaft speed sensor on the tail shaft of the transfer case. The output shaft speed sensor is a sensor the registers the speed of the output shaft and lets the computer (ECM) know how fast the vehicle is going. If the output shaft speed sensor is working properly, then there is an issue with the electrical wiring from the output shaft speed sensor and the dashboard. If you need further assistance with the speedometer and 4WD acting up, then seek out a professional, such as one from Your Mechanic, to help you.

ANSWER : The compressor clutch relay on these vehicles are a known cause of sticking on the compressor clutch and overheating the A/C compressor clutch coil. Replace the A/C relay to see if it cures the clutch going bad the next time you do a compressor clutch replacement, or replace it now if you have just replaced the clutch.

ANSWER : Hi there. If you are working on an older OEM Impala, it’s more likely than not that the wiring is your problem. In some cases, when you try to start the vehicle and you get a single "click", it’s caused by the battery not having enough cranking amps. However, it can also be caused by a faulty ground, a bad starter or ignition relay or the starter itself. If you’re restoring the vehicle, it’s probably a good idea to by a new wiring kit and start from scratch, by also replacing the starter and ignition relay as well. Also, if you’ve recently painted the interior, check the ground connection; as some times fresh paint will cause a bad contact.