Dashboard panel loose above the radio/fuel display

ANSWER : The switch you are referring to is vended with the required electrical and fuel schematic (I just looked in the box) that answers your installation question. If you want an advance view, here is a link as well. Yes, you need a return line and just refer to the aforementioned link. If you are retrofitting back to OEM, I strongly encourage you to buy the original Factory Service Manual (FSM). There are lots of details attending this system and obviously it is difficult to recount it all here. The FSM will make your life much easier and you can then make sure your installation is perfect. Alternatively, YourMechanic can dispatch a certified mechanic and perform the whole retrofit and check out if you desire. Just request and schedule a generic service such as fuel pump service and the mechanic will come to your location and estimate the parts and labor required. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : You need to look at the theft light on dash to make sure it comes on and goes off when you turn the key to the on position. If light comes on and stays on then your theft system is causing the fuel pump to not be engaged. I recommend you check the theft system and then scan the computer for theft system codes. You may need to reprogram the keys to work or you have an bad sensor for the ignition key in the steering column.

ANSWER : Hello,
You may want to try checking the fuel pump relay. The relay wires should have ground on two wires, power on one wire and switched power on another wire. To activate the fuel pump your ECU actually connects one of the ground wires to complete the circuit and send power to the fuel pump. If the wires all have power running through them, then it is likely you have a faulty relay. The wire coming from the fuel pump is the other ground wire. I would recommend having an expert from YourMechanic come to your location to diagnose your wiring as this can be very difficult and time consuming without the proper wiring diagram.

ANSWER : A professional mechanic would require roughly 5 hours. (If just the regulator is replaced that takes about 1 hour). Some parts, as noted below, cannot be re-used, you need a precision inch pound torque wrench, FSM instructions (and TSB updates if applicable; procedure was changed in 2007 for instance) and the system has to be bled when done.

Below is partial list of steps, copied and pasted directly from the service manual:

1. Disconnect battery and put protective material in front of the charge air cooler (CAC) or damage to the CAC may occur.

2. Remove air cleaner assembly.

3. Disconnect the oil drain tube from the crankcase vent oil separator.

4. Loosen the air cleaner outlet tube clamp and detach the air cleaner outlet tube from the turbocharger.

5. Remove the bolts, the crankcase vent oil separator and the air cleaner outlet pipe as an assembly.

6. Remove and discard the crankcase vent oil separator press-in-place gasket. (To re-install, tighten to 13 Nm (115 lb-in).

7. Disconnect the PCM electrical connector (BE SURE BATTERY IS DISCONNECTED FIRST!) and retainer. Disconnect the in-line electrical connector and position the engine wiring harness on the engine.

8. Remove the pushnuts and the glow plug module heat shield.

9. Disconnect the high-pressure fuel injection pump electrical connector and detach the retainer from the glow plug module bracket. Disconnect the glow plug module and the exhaust gas recirculation temperature (EGRT) sensor electrical connectors, detach the wiring retainer and position the wiring harnesses aside.

10. Remove the nut and position the ground strap aside. To install, tighten to 13 Nm (115 lb-in).

11. Remove the engine wiring harness bolt. To install, tighten to 13 Nm (115 lb-in).

12. Remove the heater supply tube nut. To install, tighten to 13 Nm (115 lb-in).

13. Remove the bolts and the glow plug module bracket. To install, tighten to 13 Nm (115 lb-in).

14. Remove the nut and position the transmission fluid indicator tube aside. To install, tighten to 8 Nm (71 lb-in).

Warning: Do NOT disconnect the glow plug electrical connector before dislodging the seal from the valve cover or the wiring harness may be damaged.

15. Using an appropriate tool, dislodge the glow plug wiring harness seals from the valve cover.

16. Disconnect the glow plug electrical connectors by pulling on the glow plug wiring harness tee above the seal. Remove the glow plug wiring harness.

17. Remove the nut and position the crankcase ventilation drain tube aside.

18. Disconnect the wiring harness retainer from the valve cover stud.

19. Disconnect the wiring harness retainer from the generator bracket.

20. Disconnect the A/C pressure switch electrical connector. Position the harness aside.

Warning: Do not bend or flex the heater supply tube or damage to the tube may occur.

21. Remove the stud bolts, bolts and the valve cover. Remove and discard the valve cover gasket. To install, tighten to 9 Nm (80 lb-in).

Warning: Contact with exposed fuel injector wiring, if energized, may result in electric shock.

Use care when working on or around energized fuel injector wiring. Fuel injector wiring supplies HIGH VOLTAGE to operate the fuel injectors of course, you disconnected the battery though.

22. Disconnect the fuel rail pressure (FRP) sensor electrical connector.

Warning: Fuel injection equipment is manufactured to VERY precise tolerances and fine clearances (think space shuttle). To prevent fuel system damage, it is essential that absolute cleanliness is observed when working with these components. Always install fuel system caps on any open orifices or tubes.

23. Remove the FRP sensor. To install, tighten the FRP sensor in 2 stages.

Stage 1: Tighten to 7 Nm (62 lb-in).
Stage 2: Tighten an additional 40 degrees.

24. Bleed the high-pressure fuel system.

If you feel like this job may be too overwhelming or run into any issues, consider YourMechanic to get it done. One of our mobile technicians can come to your home and replace the fuel pressure sensor at your own convenience.

ANSWER : Hi There,
It sounds like you may have a clogged fuel injector or potentially a faulty injector that is fried internally. I would suggest testing them if you have access to a multi meter. Disconnect the injector from the electrical connector and set your multi meter to Ohms mode and measure the resistance of the injector. After testing all injectors, compare the resistance. They should be the same or very close. If they are not, they will likely need to be replaced.

ANSWER : Hi there – I suspect you have weak power getting to the fuel pump. I would first check the voltage coming out of the fuel pump relay. If the contacts in the relay are burned, you will not get reliable current flow to the pump. Check the fuel pump ground as well (voltage drop across the ground, not just continuity). I recommend a fuel system inspection performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hi there – the metal component you describe is a fuel check valve on the fuel return line. Its function is to maintain a small amount of pressure in the fuel system so that starting does not require the fuel pump to run very long before the engine will start. Having replaced the fuel pump and fuel filter, I would check fuel pressure while the car is running. This is to check the fuel pump relay for burned contacts that won’t support full electrical current to the pump, and for proper fuel pressure – a malfunctioning fuel pressure regulator could also restrict power and higher speeds if pressure is too low. I would recommend an inspection of the fuel system by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hi there. You can scroll through the areas and the item that you want to have visible like the speedometer or rpm’s, then press the check mark and the system will go to that setting. You cannot back out of the system while driving as the system is made for a display of features while your vehicle is in motion. If you need further assistance with your dashboard messages, then seek out a professional, such as one from Your Mechanic, to help you.