Car turns over but when in gear won’t move 2009 Buick Enclave

ANSWER : Hello – check fluid level in the transmission, and for problem code, whether the Check Engine light is one or not. I suspect it will be. This sounds like a failure internal to the transmission, clutches, valve body or a wave plate. There is also a Recall (#09V073000) for the shift cable for this model, so it’s possible this problem is related to this recall, and the transmission not being in any gear due to the shifter. Make sure this Recall has been repaired first. If this doesn’t resolve your problem, I recommend a transmission inspection by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

ANSWER : Hello there. The charging system on the car may not be charging the battery as you drive and the systems that keep the engine running are priority so the engine will stay running until the voltage drops below about 9 volts but the lighting and some other accessories may cut off above this voltage first. You should have the charging system tested to see if the alternator needs to be replaced.

ANSWER : Hi there. If you can turn on the engine, then the engine did not lock. This could be a cause of the transmission having an issue. Check the transmission shifter cable to see if it has broken or came off of the transmission. If the cable is fine, then it is possible that the computer has put the vehicle into limp mode making it not able to move. Keep in mind, if your engine was running hotter than normal, the engine could be running fine but the transmission could have overheated. If you need further assistance with your vehicle, then seek out a professional, such as one from YourMechanic, to assist you with the vehicle not moving.

ANSWER : The transaxle is not engaging internally to the axle shafts inside the transaxle or you have one or both axle shafts disengaged from the transaxle. The fact that the speedometer moves when gear is engaged and clutch is released shows the speed sensor in the transaxle is getting turned.

You will need to have the vehicle raised and the axles inspected for broke or stripped shafts. If the axles do not have anything visually wrong with them then hold one wheel and try to turn the other wheel while transaxle is in gear, with engine off, to see if the wheels are locked together. When you spin one wheel the other wheel should turn in the opposite direction. If it does not then the problem is in the transaxle differential gears and the transaxle would need to be removed and disassembled to find the broken internal components.

If you need some assistance with this, consider YourMechanic, as one of our mobile technicians can come to your home or office to diagnose your acceleration issue and help make the necessary repairs to get you going again.

ANSWER : Hi there. The symptoms you’re describing with your boyfriend’s 2002 Grand Cherokee appear to be related to a broken or worn out ignition switch or relay. The ignition switch on the inside of the steering column is attached to multiple electronic connections that send signals to a relay box; which in turn, sends the signal to the individual components. The issue could be related to the ignition switch, the relay, or any of the components in between. If you want to have the fault pinpointed in person, I would have this starting issue inspected by a trained professional to ensure that the correct repair is made.

ANSWER : Your probably correct, it sounds as though your battery is done. But it also sounds like you have charging system issues. I’m not sure that fixing your battery and charging system will solve the problem with the car shutting off, but it’s possible that it will and it’s a darned good place to start. By contacting Your Mechanic, you can have a technician come to your home or office to check out your car and help you figure out what to do next.

ANSWER : If the clutch mechanism is releasing properly, and the shift linkage is not malfunctioning, your transmission will have to be removed from the vehicle and inspected. Once a transmission has been removed from a vehicle, if the problem is a broken or worn part or parts, and the transmission has 100,000 miles or more, the most cost effective approach is to just simply rebuild the whole transmission. There are transmission rebuild kits that are sold just for this purpose. Rebuilding a transmission is no big deal and is indeed easier in many respects than rebuilding an engine. You can rebuild your transmission right in your own garage. You can NOT rebuild an engine in your own garage due to the highly specialized, and extremely costly, machine shop equipment required. Occasionally, mobile mechanics will take on a transmission rebuild job especially as once the mechanic removes the transmission from the vehicle, it is just simply a modular unit that can be easily transported to a mechanic’s shop and rebuilt right there and then returned to your vehicle. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.

ANSWER : If the clutch lever, on the transmission, is functioning something has mechanically failed in the clutch and/or the transmission. If the clutch failed, and you heard gears grinding, as you tried to shift the transmission, some damage may have been done to the transmission. Even if just the clutch has failed, the engine and transmission will have to be separated to find the cause of the failure and worn out or broken parts will likely have to be replaced . To request an inspection, the recommended service is clutch system diagnostic. If you request that diagnostic, the responding certified mechanic will evaluate what you have and let you know of your repair options and costs. If you have further questions or concerns, do not hesitate to re-contact YourMechanic as we are always here to help you.